Winjet Fog Lights OEM Series for [2005-2015 Nissan Xterra] [2010-2017 Frontier][2018 2019 Nissan Frontier] with H11 12V 55W Halogen Bulbs Fog Lamps Replacement w/Wiring and Switch Kit Clear Lens

Nice kit, it came with everything you need. Now a few things to consider before buying and installing this: 1 – This kit is only for the plastic bumper, if your Frontier has the metal bumper DO NOT buy this, it will not fit. 2 - Check if your Frontier already has the harness, it should, but not all have the factory harness. Mine had it; it was strapped to other cables. So, having the harness was very helpful because I didn’t need to use all the cables and relay that came with the package. 3 – If you don’t want to use the switch that came with the kit, you need to buy a new signal light switch with the fog light option. Spend a few extra bucks and buy one that’s Nissan OEM. Now, for installation; since my Frontier already had the factory harness half the job was done already. Some people said that they install these without talking out the bumper; I started without taking out the bumper and it was a real pain, so, I spend some extra time and take the bumper out. With the bumper out I also noticed that my front mounts were worn (that was the weird noise I was hearing), so, I bought the mounts and change those as well. Installing the lights on the bumper was “easy” I had an issue with one of the clips, but, once that was fixed, installation was easy. Put the bumper back; connect the harness and that’s it. Forgot to mention that I needed to change the signal light switch, with one that had the fog light option, but it was not that hard.

I was a little nervous about buying these foglights for my 2016 Nissan Frontier S but I finally installed them last week and they are high quality and installation was relatively easy. The provided wiring diagram was helpful, but be prepared to get creative with where you choose to run the wires. I installed the provided fuse and relay boxes next to the passenger side fuse box on my truck (on the same bolt) and then ran the wires down to the passenger side light, then over along the inside of bumper to the drivers side light, up and over the horn compressor and then through a small rubber plug leading through the firewall to the switch in the interior. The light housings fit perfectly (there is a 1/8" gap between the lower bumper and the light, same as OEM). The switch fit perfectly into a blank switch housing on the dashboard. The supplied wires were long enough.

Leaving 4 stars for now as i JUST installed them 10/01/20 and i want to see how well they hold up. OEM's brought over 100k miles of use before one lense broke (probably rock) and one light/mount got knocked completely off it's bumper mount (broke mounting tab on LIGHT mount thankfully and NOT the bumper "ear" tabs it rests on) in a storm. I narrowly missed a HUGE tree falling over U.S. 29 in Nelson county but the very tip of the limb as it fell across the road smacked my fog lamp/mount completely out of socket, lol.. Anyway, point of all this is these were perfect and quick fitment replacement for the OEM mounts/lights/harness plugs and also a great value in cost as it comes with a complete wiring harness kit and switching and fusing if you DIDN'T already have OEM harness connections in place and a switch.

I bought these to replace a broken one on my truck. The install isn't terribly difficult, more awkward than anything. The tools needed are a phillips screwdriver and a 10mm socket (with a very short handled socket wrench). If I have time, I'll post pictures... To replace a light and two bulbs took me 30 minutes. One of the bulbs included with the light had a broken bracket. This wasn't an issue for me because I ordered a pair of LED replacement bulbs a few days before ordering the lights.

The lights work and look great. The hardest part of the installation was the removal of my front bumper, but a few YouTube videos later had removed it without breaking anything. I was concerned the fasteners on the light fixture would wobble loose on the bumper attachments but they held up good. Its very sturdy. I've tapped hard on the front of the lights and they are staying put. I had an empty console spot for the switch and it fit perfectly. My hardest part was finding a 12 volt switch outlet wire. Considering I don't play under the dash that often a voltmeter and about 40 minutes was able to find a switch 12v wire to attach to. I need no adjustments to the lights. I guess they come preset. I like them.

1) The clips for mounting the lights are completely wrong. I wound up having to hot-glue the stupid things into place. 2) I threw away the harness wiring; it was already pre-installed on the vehicle. Why re-wire? 3) Answer to #2 above: The lamps have an elongated guide key, which pushes the factory harness connector away! 4) I had to use a fancy scan tool to check correct operation of switch and relay before I figured out #3 above!! 5) A fifteen minute job turned into an all-day nightmare thanks to "all of the above". Good thing I saved on this kit!

Fit well and worked.

Instructions included really helped me with setup. Moisture already built up inside so it's not waterproof. Still loose after mounting so I used hot glue to keep it from moving. Best way to install is by removing the bumper. Just a few screws, plastic anchors and clips to deal with and installing is a breeze. Check if your model already has the wiring built in to utilize the factory setup. All you need is to replace the switch with replacement that has fog light option.

Muy fácil de instalar, recomendado

I'm no happy whit the product after two weeks install The water got into them when washing the car this product it's no waterproof or water resistant!

الاضاءة ممتازة و عريضة مناسب لنيسان اكستيرا 2012

Exact same ballast and bulb for 25% of the price... Fit perfectly and works great. I did switch out the bulbs before I installed them for LEDs.

Cometí el error de pedirlos no me cerciore de que son para defensa de plástico y los ocupó para defensa metálica así es que no los instale