AUTOOL Ultrasonic Fuel Injector Cleaner Tester Support Petrol Motorcycle Automotive Fuel Cleaning

This is a nice machine for the money. It seems to be made quite well. The instructions seem to be well written and fairly concise. I really like the machines size and it works quite well. Filling the injector cleaner into the machine is something that needs to be watched carefully. The fluid level on the machines side, has fill indications. If you over fill the small internal tank it will leak all over the bench. This machine will give your injectors a good workout and test them well. A machine like this is great to have if you have fuel injected vehicles. If you take your time and do all of the cycles, your injectors (if they are good) will be really clean if the fluid is well chosen .

Works really good

I am a novice engine builder/gear head and I love this thing. Use it regularly and really like it. Ill run multiple injectors and now can see which ones spray the closest and throw those together etc...

This tool is a great concept, and it really works (the first time) if you're careful. If carb cleaner touches the plastic electrical pin connectors or the front plastic panel, the plastic of these parts will melt. The manual is poorly written. Critical omissions: It doesn't tell you how to fill the reservoir; It doesn't describe the process of dumping the vials after the flow test (that's what the little handle is for, in the center of the vials); And it doesn't say how to empty the reservoir after the work is completed (you must tip the unit on it's side to empty the reservoir). Parts of the tool appear to be well-made, while other parts (e.g., the dump valve for the ultrasonic bath and the aforementioned plastic parts) are really cheap or made of the wrong material. 2 or 3 sets of extra pin connectors should have been provided with the unit, plus 2 or 3 plastic front panels, however, the pin connectors can't be unplugged. I purchased a used Mercedes wiring harness on Ebay to scavenge the injector pin connectors. I'll try cutting off the Chinese connectors and splicing on the German connectors, which are solvent-resistant. I love how well this machine worked, but I've used it only once. I tried to dump all the carb cleaner from the unit, but it remains to be seen if lingering vapors will damage internal seals. Next time I use it, I'll update this review.

Excelente calidad precio y cumple sus funciones Perfectamente

So, I've had this for a year. It is stored in my shop in a cabinet. I've used it to clean a grand total of 16 injectors. Works fine, EXCEPT now one of the electrical leads from inside the control panel to the injector harness IS NOT sending any signal. REALLY!!!!! Cleaned 16 injectors, which were not horrible, nasty junk yard parts! SO, now I can only clean three injectors at a time. Typical Chinese crap!!!!!!! Just waiting for the next lines to fail. I'm sure I'll end up with a $250.00 paperweight inn the near future.

Works great does what I need it to do. Saved me a ton of money.

Bought this for my motorcycle repair shop. It works great and the guys are really happy with it. Quality is great!!!

I like the ultrasonic cleaning. I like the graduations of the cylinders. I need to use it a few times more to learn its abilities and limitations. Messy when done as solvent leaks out when removing injectors. It can be a bit messy because of that. Not a deal breaker at all though.

I bought it after 7 days I am facing leaking problem . Not good quality

صغييير

I tested 32 injector , cars and bike . First thing the psi gauge is not accurate , should be a 0-60psi or a 0-100psi not a 0-150. Very hard to adjustnat the same pressure over and over. Pump is barely able to maintain 40psi with 24lb inj but with 80lb inj not able to maintsin 35psi . So not made to test high flow injector. Thinks that is very annoying is at the end of each lo long test , the main board is reset itselft to the base idle (02) test for 10min , and probably fuel pressure too becaus i have to raise to 40psi all the time. Oh and instruction is very very not informative , better check on youtube.