- 2in Lift Block Kit for F150 (2004-2020), Rear Leveling Block with Extended U-bolts Compatible with Ford F-150 2WD 4WD, 2 Inch Suspension Leaf Spring Axle Ubolts Set

Purchased the front strut spacers for 1.5" of lift and installed on my 2018 F150 3.5EB Crew Cab 5.5' Box Lariat FX4 ~40,000 miles. Had a bad IWE actuator, so it was somewhat convenient to tackle both the spacer install and hub replacement at the same time, nearly all of the same suspension components need to come apart to do these jobs. The spacer kit is very nice. The spacers themselves are nicely machined aluminum and anodized black. They seem like they should hold up well. I discarded some of the hardware that came in the kit, sometimes the hardware that comes from overseas is poor quality. Did this just to be safe. I used the socket head screws but sourced my own stainless flat washers for them. Then for the 3 nuts that go back on the top of the strut tower on the frame of the truck, I re-used the factory nuts, they are nice large flange locknuts. I used my stainless washers and locally sourced nylock nuts to fasten the spacers to the strut assemblies. Tip #1 - due to the 3 bolt pattern on the spacer and strut plate, you need to rotate the strut plate 180 degrees on the strut assembly. I put the lower part of the strut in a vice and used a pry bar spanning 2 of the 3 studs on the strut plate to apply torque to the strut plate to spin it. I spun in the wrong direction and the spring started to climb out of its ramp pocket. Give a little WD40 spray around the lower spring retainer, and spin in the direction that it does not try to climb the ramp on the retainer. Tip #2 - on my install (1.5" of finished lift), the thickness of the spacer is a bit less than the length of the studs on the factory strut plate. If left untouched, the spacer may not properly sit in the strut tower in the frame. The strut plate studs protrude slightly above the top surface of the spacer. I ground down the strut plate studs and filed the edges of the threads, to avoid any issues. Tip #3 - my factory struts have pressed in lower bolts where the bottom of the shock mounts to the lower control arm. That makes the overall strut assembly "longer", meaning the lower control arm needs to be pried down further to fit the longer strut assembly back into the chassis. Since I was also doing the IWE hub replacement, 2 things made it a lot easier to pivot the control arm down lower. First, having the CV axle removed from the front hub, so you aren't fighting trying to "stretch" the CV axle as you pry down the lower control arm. Second, I removed 1 nut (on each side of the truck) from the stabilizer bar link, to disconnect the stabilizer bar from the lower control arm. This then allowed the lower control arm to be easily pried low enough to install the strut assembly. Overall very nice product, good install. On the 1.5" lift version, at full suspension droop, there is very little clearance, maybe even just a bit of light contact between the coil spring and the inside of the upper control arm. I do not off-road so it is very unlikely that my suspension goes to full droop. The truck needed a minor alignment after the install. No noticeable change in ride, after all, the same shocks and springs are carrying the same load. Headlights needed roughly 2 clicks of adjustment down to shine in the same spot on my garage door at 25 feet away. Most of the rake is now removed from my truck, instead of the front being ~2" lower, it is roughly 1/2" lower. No noticeable change in highway fuel economy (air flow over and under truck might have been altered and could potentially affect mileage).

Easy to install and leveled my truck just the way I wanted it .

It fits 2011 F150 XLT

Great quality made product to place on my 04 f150 lariat crew cab 2WD. I wanted to level the front with the rear for a more defined look. Company shipped out and arrived earlier than expected. Very easy to install on top of new Gabriel ultra ready struts. Thank goodness I had my friend mechanic help me install the struts bc the width of the spacer on top of the strut required some serious force with the assistance of a long extension bar to pry down on lower uca in order for the strut to fall in place and line up with the three mounting holes. By the way, if you need to replace upper control arms now is the time bc you will have to take struts back out in order to get the side mounting bolts out and you will run into the same issue but with another helper you can do it. Final results came out better than expected as it looks really good. The rear measures 471/8 and front measured 47. Could have probably went with the 2 1/2 level but glad I didn’t bc I like the level look. Would have completed myself but like I said earlier glad to had the help of my mechanic friend.

No issues

Fit and worked great. Beware if you have a 24-25,l or maybe even earlier models, you will need a camber bolt kit installed and aligned after for this to work. Far from plug and play. I got a nice surprise when the alignment shop told me without camber bolts, it can’t be aligned and I was stuck with 3° negative camber till I got the bolt kits.

Truck looks good and price was cheap

These blocks are pretty solid and fit my '20 F150 perfectly. The U bolts were pretty long though so I took a grinder and cut off the remaining threads which was about 2.5 to 3 inches. Other than having to do that, installation was a breeze. Just put a 4x4 block on your floor jack and raise the body up under your leaf springs to get the blocks in and that's it. Throw the new U bolts on the existing axle plates, tighten and you're done!

Exelente Calidad … lo único mal es que describe en la descripción que mide 1 pulgada el cual mide 1 1/4 pulgada… lo cual levanta poco más de 2 pulgadas… si realmente midiera 1 pulgada si levantaría las 2 pulgadas como lo describe de ahí en más todo muy bien

Good product and received next day

The product seems to be good quality and better than competitors (metal vs plastic) hope they will last the life of the truck

Well made, as described arrived on time AAA+++

Fit perfectly on my 2009 F150 FX4. Easy to install. Machined nicely. Only issue I had was the supplied nuts were loose fitting on the bolts and also had missing hardware. Customer service was excellent with resolving my issues.