Edge Trim Rubber Gasket WELTING T-Style 30' FEET - with Alignment Tool for CAR and Truck Wheel Wells - Double Edge - Length 30’ FEET - Automotive Adhesive Tape Bonds to Flare

Hard to see because it’s so small but the photo is a bushwhacker fender trim on the left and a King Fender flare trim on the right. The base is slightly smaller on the king, by about a millimeter but the “T” on top is about a millimeter larger. Overall, it fits as a good replacement. I did try to order Bushwacker trim but the descriptions are so vague without distinction, it is difficult to order the correct one. I returned one incorrect order, and after shipping it myself and a restocking fee, it was basically a waste of time and money. The King trim clearly shows what shape it is with a better description. It works and is as easy install. The trim I removed was 7 years old and needed removal for paint but it lasted. We will see if this trim holds up… if not… I will be back to edit this.

This product is easy to install and mold to what ever you are using it for. For me, I used it when I was installing new fender flares on my truck. Just make sure you use alcohol to clean the surface or channel where you are going to use the trim. This will remove grease and other residue that will prevent the adhesive from sticking to the trim. Overall I am very pleased with this product.

It was a challenge to put on in corners and sharp curves. It's rubbery and easy to position. The adhesive worked well for me, its gummy so you can move it around a little and fix places easily. The best is the consistent line it makes sealing the fender flares up against the truck. I'd buy this again.

Was a bit skeptical about purchasing when reading reviews but went for it and it worked out fine. Got it installed on the 4 fenders in an hour. The roll had some of the 3M tape peeled off when I opened the package but it doesn’t seem to have affected the quality much. Ended up just peeling the tape off as I was putting it on. Satisfied the way it came out and looks good for what I’m using it for.

So a few things this strip is nice for one reason the outside edge is larger than most which let's it seal the gaps really well but the bad part is the adhesive side is not thick enough at all and because of that it has a hard time sticking and staying in place. I just used it today I got one flare done pretty well. 2 I had trouble with the seal staying in place on the flare and the last one it wouldn't stick at all. And yes I cleaned all the surfaces and no I did not pull the adhesive strip from the whole thing. It's not my first time doing this. So all in all I'm pretty disappointed.

50/50. The adhesive didnt stick to anything. So I had to use tape to keep it on place then install the fender, then remove tape. Pain in the arse! Looks great when on there and does the job, but have fun installing.

The finished product is much better than the one supplied from Bushwacker. No joke though, not easy to install. 4 fenders took about an hour just to do the fenders. Had to dab a small drop of superglue at the sharp edges to hold but other than that super happy with the look. Very clean lines and really cleans up the looseness of the OEM adhesive U-Shape from Bushwacker.

Not sure if adhesion is going to hold. Trim doesn't seal up gap very tight. Not sure why. Seems like the angle it must be applied to ensure adhesion to a good surface, makes the trim point up, instead of protruding toward the body of the car. The fender flares is a little too thick maybe.

Bon produit

Top

Great product

I ordered this in hopes that it would fit on my fender flares, but my flare is thicker, and this seal will not seat on it properly. The product looks good and should work well, but not for my application.

Yanno I super excited to finish my fender flares, but honestly, looked wayyyyyy better with the gaps. This stuff sits so off and bulky on the flairs and creates a wayyyyy bigger gap than my fender flares already had. The rubber doesn’t even have curve in it to actually try to round and curve itself to touch the body, just sits straight up. Literally this thing is usually. Not to mention how horrible this stuff sticks, had to use my screws to hold this rubber down as they keep sliding off. For that this thing cost, and the amount of time I spent for this dumb looking finish. I’m so disappointed. L product.