PRO BIKE TOOL Bike Wall Mount - Horizontal Indoor Bike Rack for 1 Bicycle - Bike Rack for Garage - Safe and Secure Bike Hook for Road, Mountain or Hybrid Bikes - Bike Hanger, Bicycle Storage

The rack works great for my 23lb road bike. The instructions were clear and straightforward. The adjustable arms are convenient for maximum stability.

These are great bike racks for our garage. They keep our bikes up and out of the way while saving space. These racks make our bikes more available to be able to reach verse being in a shed. Definitely recommend these to any cyclists looking for a rack that is strong, easy to pu lt up and allows your bike to be out of the way.

This is a great bike storage system, highly recommend. Ok, enough about how great it is. For me, I want to know tips how to install it and you probably do too. As you can see, I installed 3 holders. First step was to find the studs behind the sheet rock. I used a quality stud finder but to double check the studs exact location I used a finishing nail and hammer to find the exact sides of the stud. Glad I did because some of the stud finders locations for the center of the stud were not right.You can use longer screws than those that come with the kit (3) and mount the 3 holes of the bracket into one stud. I read where some have said this works. Didn’t seem it would be real stable so I decided to mount a 2x6 across two studs. A 2x4 is not wide enough for the bracket. I cut the 2x6’s 22” long so they overlapped the end of each stud by 3”. I attached the 2x6’s to the studs using 5/16 x 4” lag screws. I used 4 lag screws per 2x6, two on each end.You’ll need a impact driver to get the lag screws thru the board and into the stud. A regular drill won’t do it. If you don’t have an impact driver you could always muscle a socket wrench. After I drove the lag screws in as far as they would go I did have to use a socket (1/2 for the 5/16 lag screw) to finish tightening them down.I measured the bikes with the holder/ bracket to get the spacing between bikes. My measurements resulted in a spacing of 40” from the top of one board to the top of next board. For my bikes it was perfect. Your bikes may require different spacing.These type of wall mounts are perfect. Unlike other systems that are one position, usually horizontal, these allow you to adjust the arms to fit the different types of cross members as not all bikes are alike. They’re pricey, but I think they’re well worth the money. The 2x6x8 was $12.00 and the 12 lag screws were $9.00.I hope this helps if you decide to purchase these.

Well made, easy to mount into a stud with the provided screws. Rubberized arms hold the bike securely without marring the finish. With the bike level the front wheel doesn’t move so no need to use the included wheel bungie. The bungie quality does seem fine though, nothing special but it works. Not sure why others had an issue - maybe pulling it too tight. I’ll probably but another to hang my other bike above the first one.

This mount looks great but needs some improvements... the locking tabs do not always stay locked... the mount is universal so the distance from the wall to the bike even at the closest setting, for my bike, still extends too far away from the wall in a 10' wide garage to allow a vehicle to drive in without risk. With that said... I still like the mount... its stable, and looks good and with a few modifications works well.

For a lightweight roadbike, but this could easily hold 3x the weight

I've been using this for about two months now. This helped me save space in my 1-car garage as I was able to lift it up near the roof and fit a ton of stacking bins and toolboxes underneath.The construction is sturdy, just make sure you screw into a stud, I don't know why they would ever include plastic wall anchors. Don't try it, I guarantee they will fall out of the wall very quickly.

Love these bike racks. I purchased two and will need a third. Super easy to mount on the wall. The only help I needed was lifting the bike to place on the rack. Only three screws to insert into the stud. A tap tap then screw into the stud. You will not regret this purchase.