Monoprice Low Profile 22 lb. Capacity Speaker Wall Mount Brackets (Pair) Black

We bought these after another brand I tried just felt flimsy and awkward. Our speakers are around 8# each and this design easily holds them without worry. I like the 2 part design, so you can easily detach speakers without having to use tools. The base is anchored to the wall and a second piece connects to speaker and can slide down into the plate. Also, the flexibility of the ball-joint type system makes for super easy adjustment. For the brand of speakers I purchased, the middle center speaker had holes too far apart for a single mount but could just place 2 mounts side-by-side to make it work. As we tried to place these high in the room, we weren't able to install the top screw to keep things in place. Not terribly bothered by this because they feel so sturdy, I'm not even worried about it. These are perfect for smaller spaces as they are super slim and keep speakers close to the wall and well out the way of anything. Solid product all around and great price compared to other systems.

I bought a Logitech Z906 5.1 system for my garage and needed some mounts. Packaging is good. I bought two sets (4 mounts total), and one box was damaged, but inside, everything was fine and well packed. The mounts themselves feel pretty strong and I am confident they will hold just fine. What is hard to tell from the product page is that use a ball joint mount for the speaker, so the speakers can swivel, well I can't give you an accurate degree, but it swivels in a sphere (up, down, left, right, etc). It also comes with two speaker screw supports - one for small speakers, like the Logitech, and one for maybe a medium size speaker. I am not certain how much weight these will hold, but it holds the Logitech, so I'm good; I would suspect nothing larger than a medium weight book shelf speaker. The wall mount bracket comes with 4 screw holes. All mounting hardware is included, however, I used 2x 1 5/8 inch sheetrock screw and 2x 2 inch wood screws to mount the brackets. the speaker attachment slides on and down to lock into place, and then you can use an included screw to lock it in place, but to be honest, I didn't need it - from screwing the bracket in, it flexed the wall mount bracket a tiny bit, so sliding the speaker mount bracket onto the wall mount bracket required a soft rap of my pliers' rubber handle to get it to slide/lock down - totally fine with that. Best way to do that is get it into place and hold with one hand, then tap the top with your tool to bring it down - watch out that you use something softer like rubber so you don't gouge out the wall, but you may mark up the wall if inside the house where you care, so maybe use a flat head screw driver and then tab that so you don't bump the wall trying to push the bracket down. Once you mount the wall bracket, you take the speaker bracket and remove the giant 3-star nut. It screws off by hand to reveal the ball socket. Put the ball speaker screw in the socket, and replace the 3-star nut - it's got quite a few threads, and they are thick, so it seems pretty sturdy. From there, determine if you need the small or large speaker support attachment (I needed the small one) and then screw in your speakers. don't overtighten. Once done, take the speaker support bracket/attachment and lock it down tight again the back of your speaker. Hook up the speaker wires and mount your speaker on the wall bracket - DONE! That's it. I mounted 4x speakers in two parts of the garage, ran/custom cut 5x 16 gauge Amazon Basics speaker wire for the Logitech speakers, stabled them to the wall/ceiling where appropriate, and tested the system in 45 minutes. I am considering buying a third set (because I'd like to mount the center channel and these only come as a set of two, so I'd be wasting one, but it would be worth it as I would definitely buy these again (considering using them for my inside 5.1 system in the family room (fronts only, rears are mounted on ceiling already).

I used a pair of these mounts to hang a center channel speaker. It is a Klipsch with two (2) threaded inserts in the rear, 14" apart. I was pretty nervous about getting them on the wall accurately enough to line up perfectly, so I measured twice and used a laser level, etc., and that part of it worked out very well. It is cleanly installed. Here is the problem: The manufacturer provides screws and drywall anchors. The screws need appropriately sized anchors to provide a good grip on the drywall. This means you should feel resistance as you thread the screw as the anchor spreads behind the drywall to grip the back side. The manufacturer may not understand this. I noticed as I threaded the screws that there was no resistance, and they never bottomed out. They kept spinning. The screws don't immediately pull out of the anchors, but it is not a tight fit, meaning the anchors are too large. I made sure to hit a stud with one of my screws, so it is OK for a while. The room it is in will be renovated eventually, so I won't worry about it. But I would not want to permanently install with these anchors in drywall only. They are cheap, so I recommend going to a hardware store and picking some up that are correct for these screws. Someone can help you if you are unfamiliar. It's worth it if you are hanging an expensive speaker over an expensive TV. The manufacturer needs to correct this mistake. Other than that, the product, itself looks and feels well-made.

I recently purchased these wall mount brackets to mount the rear speakers in my new Monoprice 5.1 system, and I couldn't be happier with my purchase. These brackets are well-designed, easy to install, and offer excellent stability for my speakers. One of the things I love about these brackets is their low profile design. They sit very close to the wall, giving my speakers a sleek and modern look. The black powder-coated finish is also very attractive and blends seamlessly with my home theater setup. Installation was a breeze, thanks to the included hardware and clear instructions. I was able to mount the brackets to the wall quickly and easily, and the ball joint mechanism made it simple to adjust the angle of the speakers for optimal sound. The durability of these brackets is also impressive. They are made from heavy-duty steel, and I can tell that they will provide a stable and secure platform for my speakers for many years to come. Overall, I highly recommend these wall mount brackets to anyone looking for a reliable and stylish mounting solution for their speakers. These brackets are a great value for the price and have exceeded my expectations.

Las bases son bastante compactas pero muy resistentes. Coloqué 2 bocinas pequeñas y 2 bocinas grandes para mi Home Theater con sonido Atmos. Las bases fueron de las pocas que soportan más de 5 kgs sin ser voluminosas. Excelente calidad en los materiales y mucha facilidad para colocarlas pues contienen variedad de herrajes que se ajustan a cualquier tipo de bocina. Sí los recomiendo ampliamente.

I recently purchased a 2021 Samsung Surround Soundbar system and for some dumb reason they don't include any mounting hardware for the 2 satalite speakers. These did the job very well!

These are very sturdy speaker wall mounts. I used them to fit pure jongo t4s. Easy to fit and hold speakers securely. My speakers are about 2.5kg. Also I can lift the speakers out of the wall mount (and replace with ease) which means my speakers are still portable. No complaints. Quality product.

I used the Monoprice wall mount brackets to hang a pair of surround speakers, Energy CB 10; each speaker is at 7.8 LB (I weighted them) and they have in their body a 1/4"x20 threaded hole; although the brackets come with a few anchors (for concrete) having in my basement only drywall I ended up using regular, standard, drywall anchors; the brackets are sturdy, well done, come with a multitude of connectors to speakers, are very easy to install, I had no issues whatsoever; I read some reviews being critical on their looks (e.g. 'Monoprice' label), but I have no idea what they expected: these brackets are hidden behind a speaker, practically invisible, nice, clean, simple; my speakers will tilt a bit downwards due to weight (see pic) but won't touch the wall and are very easy to secure in a certain position; I wholeheartedly recommend them to anybody who wants to hang speakers

Robust quality product. I have used it for mounting my surround speakers.