Geekpure 10-Inch Whole House Water Filter Housing with Wrench and Bracket-4.5 x 10 Inch-3/4-Inch Port

Just recently installed a filter and purification system. Would’ve bought the 20” version but didn’t have the room. Still extremely happy with these. Few points below as to why and thoughts during and after install.1. They’re as universal as it gets! You can buy any type of filter for these and they’re not that expensive. I installed three of them with a 5 micron, 1 micron and carbon filter.2. Install was extremely easy! Took maybe 30 minutes to unpack, assemble, and hang on the wall.3. For connections I used 3/4” sharkbite fittings with sharkbite PEX pipe. No issues with leaks, have clear markings for in and out, and worked from the get go.4. These can filter ALOT of water before being swapped. I installed two water pressure gauges, one before filters and one after filters to help gauge how dirty they are by pressure loss.5. If you’re worried about pressure loss installing these, don’t! We have a 2400 square foot house with 3 bathrooms. Our main water line is around 45 PSI. After installing these and a UV purifier, the post filtration PSI is actually 5 PSI higher when the water is running or not.6. Buy them. I spent $788 on everything you see in the pictures. That’s much cheaper than any “kit” of the same size you can buy. It takes planning but you really just need to know connections, 3/4 MNPT for these, UV filter was 3/4 FNPT, how many elbows, how many tees, then some gauges and shutoff valves and the PEX pipe is easy to cut to any length needed. Just get the removal tool in case something leaks or you need to adjust something! I rerouted some pipe after initially installing it.Great buy and can’t wait to see what these filters look like a few months from now.

Like it

... be aware that you will probably need to use a LOT more Teflon tape than what you are accustomed to using. I started installation with my normal 4-turns of tape, but this was woefully inadequate. Both sides leaked. I got one side to stop leaking after pretty much bottoming out the fitting. The other side still had a slow drip. I ended up redoing the fittings with more tape, and this proved to do the trick. Aside from the threaded holes being tapped a couple turns too deep, the overall filter housing & mounting bracket are great quality at a really great price.

Omg our last unit started to leak after 10 years and this product came in overnight for our tankless water heater, great service

This filter is a replacement for one I had less than a year. The housing cracked.

Quality product. Does the job. No need to spend more!

I had 10 x 2.5 charcoal and sand filters installed for years. I figured it was time for a step up so I changed to 10 x 4.5 charcoal and sand filters. It was easy to change the hardware. I noticed better tasting water in about 2 weeks.

Purchase 3 of these filter housing’s for several projects. The first one as a whole house water system. The second was a maple sap RO. The housings were ok not great. One was difficult to get sealed but did seal after several attempts. My main complaint was the red bleeder was broken on one of the canisters. Customer service at Geek pure is horrible, it’s been almost a month for a replacement part.

de bonne qualité

Au départ faut rincer une bonne quantité, c'est pourquoi j'ai installé une valve au drain. s'installe bien mais faut quand même de l'équipement minimum et connaître ça un peu. bien été rien à coulés.

Parfait

Filtre bien, mais pas de bypass et il faut serrer très très fort pour ne pas que ça coule....et sûrement dévisser très très très fort pour changer le filtre.

These have centering posts at the top and bottom so that the filtering element is not installed way off center like the Pentek ones I got that allow unfiltered water to enter the exit port.I now have a total of four of these and they all came with mounting brackets and wrenches, which the other brand did not.