Replacement Harman Pellet Igniter 3-20-677200 Upgrade Design 15 fins Incoloy 800 P35i P42i P43 P68 P61A PF100 Advance XXV Accentra Absolute 43 63 BA100

ignitor worked on the first try..i purchased two for my client. The most difficult part of the installation was to get the two wires zip tied after the install. I am 6'5 with large hands which made getting behind the cabinet difficult..i didn't disconnect the stove pipe and just replaced the ignitor with the stove in place. I hope this helps

Update 1/25 Igniter is dead. Got only two years out of it. Update 3/24 It seems the igniter is working again. Its been over a month and no problems of not igniting. My five year old Harman stove would not light. I talked to my Harman dealer and he mentioned its the igniter. He mentioned you can go aftermarket, or go with an original Harman igniter. He priced the igniter at Harman at $200.00 or $40.00 for an aftermarket. He added, go with original or you will be sorry. Talking to a friend who has a pellet stove, he mentioned that he bought an aftermarket igniter and it only lights every once in a while. I decided to check online to see if I could find the part cheaper and came across all these cheap aftermarket igniters touting all their great features.... Sure enough, I could not pass on the cheap price. Bought this one in December 23 and now its Feb 24 and the thing does not light. I should of listened to the two people who warned me about these cheap chinese products. Not I have to take my stove apart and install a new Harman igniter. Lesson learned.

Harman XXV stove. Igniter fit perfectly in the bracket and is a good replacement. We have three pellet stoves in the house and one in the garage/shop. This one gets used the most. Running about 18 hrs a day from mid Oct, to mid April. This is an easy part to replace and inexpensive, takes about 15 minutes. One thing that is helpful is to use a 10 d nail, bent over 90 degrees about 3/4 in from the point, to hold and align the mounting screw holes in the bracket on reassembly. The two 1/4" head screws are a little awkward to work with, the nail inserted through one hole in the fire pot will align the bracket and you can hold it while starting the the other screw, snug it up then remove the nail and put in the remaining screw.

Purchased in January 2020 - just died after a few sporadic days. Ordering another today. 3-5 years is the average lifespan for pellet stove igniters, so this one was at the higher end of the averages. I could buy 10 of these for the cost of a Harman igniter. It's a no-brainer

I have used the igniter for over a month now and having great success with it. It lights every time and the maintenance of the burn pot is minimal. It works as well as the original factory igniter.

I wish I could leave zero stars. Where my stove is located it doesn't make it easy to work on. Thats my fault. But when I buy a new part I expect it to work. This timed out 3 times in a row. Tried several different troubleshooting steps as suggested in their help section. It gets Hot. Just not HOT. Now I am going to order a REAL Harman ignitor. NEVER AGAIN. OH And customer service also sucked

The quality looks great and the igniter fit the holder well. The only problem I had was the connectors plastic insulators were larger than the originals. They wouldn't fit through the hole on my XXV Harmon to connect to the wiring. I cut off the plastic on the igniter wires and was able to install ok. It did remove one layer of protection, but the wiring protectors were sufficient to prevent any shorts. The igniter works great.

So happy to receive part!!! Worked!!! So grateful! Installation was a breeze!!

Well at first glance, it was looked different, some of the fins were not 100% crimped to the body. But it did perform just as good as the original, even a bit better, oem fire lite in 6.3 minutes, this one did it in 5.6 minute

Igniter fit well and works good so far

Concerned that the connections had very thin connectors inside the plastic. The flat blades were were made too thin .So in order to make a secure tight fit ,I had to crimp the connectors on my stove. Hope they will last? Electrical connections are essential.A bit of a job so with everything apart and the long wait on delivery I tried the igniter .So just be aware of that upon installation.Well after a month of use it stopped working. Waiting to hear from the seller

Parfait

Easy to install and works great