Lippert PSX1 RV Power Stabilizer Jack System for Automatic Leveling, Legs Auto Adjust to Terrain, Front, Rear Mounting, Heavy-Gauge Steel Frame, Powder-Coat Finish, Extend up to 30 in. - 369774

Installation was easy, product working beautifully so far. I like how the legs are relatively independent - the older set would only go down as far as the highest point - leaving the other side in the air forcing me to level by wooden inserts. And while these are not intended to lift the trailer, its nice that there is a small margin that one leg can down further than the other.

Hey...I was replacing a ruined (I dragged it over a rock ripping it off the coach) Lippert Jack with a Lippert Jack...a no brainer! This unit comes with NO INSTRUCTIONS...but that is okay, your really don't need them and I will quickly tell you how I did it.Tools needed: Floor jack, ratcheting socket wrench, wire cutters, electrical crimp tool, electrical butt joints for joining electrical wire, two wood blocks such as a 6'x6'x4" or something akin to this to lift the new Jack off the ground enough to slip the floor jack under the Lippert jack. I used the original bolts and electrical switches so I set the new parts aside for some other project.Installation Instructions:1) Find where your jack motor wire is connected to the Extend/Retract switch in the coach (I had to pry a panel off from inside the rear storage bay to reach my wiring. Cut the wire about 3" from the existing joint BEFORE the joint so you have enough wire to pull around the side of the panel concealing it for joining the new cable later. Now BEFORE pulling the wire out of the coach tape a coat hanger (or heavy string) to the end of the motor wire so you have a means of snaking the new motor wire back into the coach...it is a bugger if you miss this step! Carefully work the old wire out with the pull wire/string attached2) Unbolt the Lippert Jack to be replaced being careful to not drop it on your head...it's heavy! You should wear safety glasses so dirt doesn't fall in your eyes while you are doing this.3) Using the shipping box, flattened out, drag the new jack into position under the coach so it lines up with the bolt holes.4) Set the jack up on the the wood blocks so you have room to get your floor jack under the Lippert jack5) Place the floor jack in the center of the Lippert jack (a natural fit in the center between the two jack arms) and jack the Lippert jack up snug (but not tight!) so as to be able to move the Lippert jack a smidgen to get the bolt holes to line up with the slots on the jack. Put the bolts in but not tight until you have the jack lined up to your satisfaction. Then snug the bolts down (about 20" lbs if you have a scaled wrench...or firm but not so tight that you strip the threads of the bolt!). Remove the floor jack, wood blocks and shipping carton.6) Snake the new motor wiring up the same route that the old one was pulled out of. Using butt joints, connect the black wire to the black wire and the red to the other wire.7) Test your new jack and smile...you did it!

Exact fit. Literally took 10 minutes to install.

This replacement was exactly what I needed. Only complaint is that the old one was installed with a total of 8 bolts and nuts. This one came with only 4 of each.

We ordered two of these stabilizers. One arrived fine the second on arrived without the hardware. Amazon was great and picked up the one without the parts and sent a new one. Word of caution if you receive the stabilizer without the hardware it's most likely because the box received a hole in the box and it was lost in transport. I wish Lippert would package it better with better protection and maybe a bigger box.

I made a rookie mistake first time using our new trailer and forgot to retract my stabilizer legs before hooking back up to the truck. As I hooked up I realized my trailer tires were off the ground and all weight was on the back stabilizer legs, and as I tried to hurry and lower it back down, the legs gave under the weight, and bent. I saved a ton of money buying this replacement off of Amazon and replacing the bent one myself, instead of taking it to the shop. I'd say I'm a novice in these types of things, but the install was an absolute piece of cake. Only took me about 30 minutes to swap it out (including the electrical wiring), and the new one has worked perfectly ever since. It came with the switch to extend/retract, but I did not need to swap that out. The existing switch still worked.

Was such a quick switch out from the broken one.

My likes are it was exactly what I wanted

Recu dans les date promis et article conforme a ce commander

My original on the camper landed incorrectly and when i lifted the pin at the front to block it up bent the leg. So i bought a powerfist one from p.a., it was noisy and nreliable. Returned it and got this one.Would definitely recommend this for replacing another over any offahore branded ones.

this item is exactly the perfick t same as old onethank i saved 300$ on this item

I had to replace my old scissor Jack and this one was a perfect fit. 👍