BlueStars Ultra Durable WR9X499 Refrigerator Temperature Control Thermostat Replacement – Compatible with G.E & Hotpoint Refrigerators - Replaces AP2061705, WR09X0499

Our GE refrigerator (TBG25PAXGRWW) was purchased in 1997 (28 years old). Recently it was either cooling everything too much, or things were melting. The culprit was the thermostat (wr09x0562). Like many others, it is discontinued, and people are forced to buy new refrigerators because a failed $15-30 part. Anyway, we took a gamble with this one, which works despite the fact that it is not meant for a TBG25PA. Perhaps it is not so sensitive in setting the temperature, but so far (we have it for more than a week) it works fine. Two more points: The thermostat dial must be displaced by 90 deg. so you must learn how to set it. Also, the mounting screw threads differ from the original. But screws are easy to find. To consider before throwing away your refrigerator.

I bought this thermostat because it had the capillary tube that would serve my purpose. The real replacement was very expensive and mostly out of stock. I bought this one and had to modify the mounting strap to use it. I also had to adjust the temperature range since it was designed to be use in the refrigerator and not the freezer. There is an adjustment screw to make the temp lower but it took some experimentation to find the best setting. The original knob fit the control fine but the numbers were not aligned correctly and I had to make a label and stick over the numbers. I probably had 3 hours time with all the mods and would have lost money if I paid someone to do them.

Slow shipping, great product. Was a day late which is not good when you only have 1 refrigerator.

Have a TFX22PPDAAA fridge probably 15+ years old that started to become warm 2 days before going to vacation. I initially replaced the defrost timer due to some confusion I had trying to understand how it works (some of defrost timers have a resistor in series with the defrost motor and some of them have a capacitor in series with it - so depending on resistor/capacitor they should be tested slightly different). After I replaced it I figured out that Temp Control Thermostat is in series with defrost timer so if thermostat is defective (i.e. remains opened for some reasons) nothing will work. This thermostat is basically a small closed pipe (i.e. the stuff that looks like a wire) filled with some gas that ends up with a membrane inside the big metallic block. When temperature increases the pressure also increases forcing the membrane to push a needle through a spring to push a switch to close the circuit - once the circuit is closed it activates the defrost timer that either enables the compressor to work or (for a very short period) defrost heater to melt the ice that is forming behind the wall in the freezer. So after reading through reviews for WR9X499 (basically I was searching for WR9X599 but GE in his infinite wisdom decided not to produce it anymore) I decided to give it a try - All I had to do is to find 2 different screws, play a little bit with the wings to align the holes to screw them and rotate counter clock wise 1.5 times (when you look closely near the knob you'll see a 1.5 mm in diameter hole with a small screw - this is the one that I think allows you go calibrate it to 0 degrees F) and to push the pipe sensor through the plastic tube to reach the freezer compartment, connect the two wires to it and that was it. The freezer temperature reaches anywhere between -1F to 0F when the temp control thermostat opens and it is working for 2 days now.I could say that "Worked as replacement for WR9X599 Temperature Control" review of "Power Reader" is accurate and I avoided the hassle of buying a new fridge.PS: After I dissembled the old/faulty Thermostat my conclusion was that the switch was still working properly but for some reasons the membrane did not have enough force to push to close the circuit (i.e. remained opened all the time) - I suspect a micro fissure into it forced the enclosed gas to be very slowly released therefore the malfunction.

The temperature control on my 25 year old GE fridge was not working correctly. It would cool to the proper temps, then turn off, and occasionally not come back on. By turning the Temp Control knob on/off and jiggling it, the fridge would come back on. This got worse and worse.The part number for my temp control is WR09X0599 (also WR9X599). This part is not available anywhere. I contacted 5 repair shops and none of them would work on my fridge since the part was no longer available, and they all recommended replacing the fridge.I saw a review from Penny J that seemed to have the same problem, so I ordered this part.Short version ... it worked!! My fridge is now working properly again for $15. I did not have to buy a new fridge (and have my almost fine fridge toss into a landfill).Details on this part:- the packaging was non existent! It had been in a flimsy box inside an envelope, and had come out of the box, so it was basically shipped in an envelope. How it survived that I do not know.- I did have to bend the mounting tabs slightly to line up with the holes where the previous controller was, about 2mm adjustments on both sides- I did have to get 2 screws to fit- the temp probe part is about 4" shorter than my original X599 controller , but it was still enough to go into the freezer area and the temps in the fridge/freezer are perfect- once installed, getting the temp right in the freezer did require some adjustments to the set screw. The large temp control knob makes fine adjustments to the temp. But the small set (preload) screw makes larger adjustments. At first, the freezer temp went to 20 degrees and stopped. The set screw is located right next to where you push the larger temp control knob on. In the end, turning it 1.5 turns counter clockwise got my freezer to zero.- It is working great, zero in freezer, 37 in fridge, all fixed for $15!!

Installed it yesterday. Currently working. However, the post (used to secure the temperature dial) is not aligned properly and you are unable to adjust it. This, the temperature number do not align properly. I had to test it with my multimeter and add new temperature numbers on the dial (with a black marker). Disappointing since the manufacturer states it is a quality build. We will see how long it lasts.