Ge WD21X23461 Dishwasher User Interface Assembly Genuine Original Equipment Manufacturer (OEM) Part

Pretty easy fix for my GE Profile washer, just set the pins in the right config for your model # and install. YouTube has great videos to help!

I ordered the old style board that went out on my fairly new dishwasher. They sent the new updated board, that was a direct replacement. I only had to "set the personality" on the board, by moving the jumpers as indicated with the included instructions.Put it all back together, and am now washing dishes again!!!Fast shipping, quality parts, no worries here! Would do business with again.

I don't know what it is about GE replacement dishwasher parts, but this as well as two power boards I've ordered all smell very strongly like a cleanser or cleaning product of some sort.This UI board is compatible with a number of different dishwashers; mine is a DDT595SGJ1BB.I got it because my dishwasher stopped turning on. I knew it was on its way out because it would turn off & on randomly, until one day it just stopped turning back on. The power board showed a solid green light when connected to power, which is an indicator that the power board is good but not the UI board.You have to set the "personality" by moving jumpers on the board. From what I can find, the personality controls which buttons are responsible for which functions, and allows this board to function as a replacement in a wide range of dishwashers where the original part numbers were different. The board it replaces (at least in my model) does not have jumpers, so it's easy to overlook that.Setting the jumpers is a important step! If you forget to set the jumpers you're going to have to take the door back apart to set them, so remember to do that first before installing it. They include a paper that tells you which jumpers to set for your model based on the first 6 characters (for me DDT595), make sure to pay attention to the jumper numbers on the paper so you don't get it backwards.Disassembling the door requires unhooking the springs from the door, lifting it up, and then removing a bunch of screws from the bottom of the door. I looked up a video online but found that my dishwasher's disassembly was a little different than the video because there were some extra screws. Turns out I also didn't have to remove the vent cover like it instructed because the vent on my model is attached to the inside panel. So you may have to improvise if you don't find a video for your particular model.After installation my dishwasher started working again. I did notice one difference in functionality vs the original UI board. With the original, it would turn on when you open the dishwasher based on the door latch sensor - this one doesn't, so I have to push a button to get it to light up. Not a deal breaker though.

Internet & YouTube search suggested problem could be caused by either a bad main control panel PCA or user control panel printed circuit board. Further Internet search using "GE 2015 plastic tub dishwasher technical service guide pdf" found link to FREE technical manual which said that since "Service LED on main control board was ON & not blinking", problem MAY be user control panel BUT to check for ~13.5 VDC on pins 2 (which black/green wire mates to) & 5 (yellow/blue or yellow/black wire mates to) of connector on main control PCA (wire harness goes up door to user control panel), and if get ~13.5 vdc, problem is with user control panel, if NOT, replace main control PCA. Couple of TIPS: to check service LED on main control panel, remove screw holding cover on power-in junction box, BUT THEN ALSO remove 2 screws holding junction box so can wiggle it out of way of main control panel, as this makes it MUCH EASIER to reposition main control panel back in place WITHOUT pinching wires; ALSO my model had a round "inner door vent cover" which HAS to be unscrewed BEFORE you can separate the door plastic inner panel from the metal outer door to access the user control panel PCA; lastly, this new user control panel PCA is made to fit many models and has to be configured to match YOUR model by setting small jumpers CORRECTLY on the set of pins on the PCA, so MATCH JUMPERS EXACTLY per instruction sheet diagram for YOUR model.

This part was supposed to replace the UI board on my GE dishwasher. After installation I noticed one of the buttons for not work. I disassembled the unit and noticed the button on the motherboard is not there. All of the connections and soldered parts are there, just no button to activate the "wash zone" function. ( See image).

Easy to install one of my buttons doesn’t work but I maybe have set the pins incorrectly

Part fixed my problem with my ge dishwasher DDT595SSJ2SS. Only issue was the board came without instructions to set the jumpers (or personality ). Quick google search to find the pattern.

Easy to install with some skill/proper tools. Beats paying to replace the whole appliance