Mcbazel Arcade Game RGB/CGA/EGA to VGA HD Game Video Output Converter Board for Arcade Monitor to CRT LCD PDP Projector

First off, I always disregard when people say get an "official" Gonbes. It's getting increasingly hard to find an "official"(whatever that means anyways) version of these converters. As far as I know I've only ever used 1 legit version, and have about 4-5 other "fakes" currently running video output in some of the machines here at work that I service. I don't even remember where I found an official one direct from Gonbes themselves(maybe here, maybe Al.iexpress?) Anyhow, after fidgeting in the on-screen menus and adjusting the clamp settings these typically do great. The menu language usually needs changed from Chinese to English as well. This time around though I was having a lot of jittering on the screen so I soldered a resistor into place between the board video output and the Gonbes sync connection which took care of that problem for good. I believe I used a 1kOhm resistor. Looks and plays great to me, little to no lag as far as I can tell!

Used it to debug a set of Galaga boards for a friend using an old 4:3 VGA monitor. Worked great. Initially the picture jiggled a bit, but after I soldered a wire onto the vertical sync (see photo) on the video board and attached it to VS (the yellow wire on the supplied cable) everything works perfectly. The default setting of Chinese is a bit annoying. The seller should include some instructions on how to change it.

Awesome product. Was getting a signal not found on my Dell monitor on my Ms Pac-Man machine, installed this and now it works perfectly

Ordered this because my DDR Extreme CRT monitor is dying. It converts the 15khz VGA output of my DDR into true VGA signal that a modern monitor can display. Overall it seems to work ok. The language starts in non-english in the menu, so have to change that first. Then, the written instructions do not correspond to the on screen menu. It has no way to move the picture on the display. There is s menu item, not in the instructions but on the on screen menu, called ‘geometry,’ but it won’t activate, at least with vga input. Also my monitor had issues seeing the signal at first until i adjusted resolution settings, but sometimes on re-powering it loses the input resolution and you need to reselect it. Finally, colors aren’t the best or easiest to adjust, but it looks okay in the end after adjusting the monitor and screws on the board. Make sure you buy a dc power converter, i bought a simple 5v, 2a dc plug in adapter with multiple tips, the default tip fit the board, no cutting or soldering needed. The speed timing for ddr is perfect, didn’t need to adjust speed or delay at all. The picture is fine, better than the old CRT, but the colors are so-so. See the video for demo.

It worked well. MGA was a bit fuzzy usable.

Horrible, image is shaky and jittery and will not fully sync with my game boards no matter what I do.

Easy to install! Provides a great picture. Watch a couple YouTube videos to learn how to set it up once it's installed. Provides an excellent alternative when you need to replace an old crt monitor with a flat panel TV or PC monitor. Can't get it to work on the old 5 card draw games though. I've heard that is common though.

I am an amateur at repairing electronics and used this on an old arcade game to replace the original glass tube monitor. It was fairly easy to connect and set up although I did watch a helpful video on YouTube about setting it up.

Un ESP en plus, un fw gbs-control et a vous les scanline et les modifs pour profiter de vos vieilles consoles et ordinateurs du siècle dernier ;)

Fungerar jätte bra! Lite svår att förstå sig på i början. Men det finns guider på youtube. Man kan med lätthet få bilden precis vart du vill ha den på skärmen. Perfekt om du skall använda ett gammalt pcb med en ny lcd skärm. Men även bra att ha om du skall installera en 60 in 1 eller pandoras box.

Connected to amiga 500. used online guides to get RGB connected to the computer. took some time scaling the unit and the overscan on the a500. turns out to be a decent interface. worth the $

I'll be using this as a base for a GBS-C build for my retro consoles. My original GBS8200 I bought from AliExpress a few years back (and subsequently stuffed into a drawer untested) turned out to be faulty when I came to build it this week. The cheapest I could find on there after tax and shipping was £27 delivered (and a 2-3 week wait). This one was £21 and change, and arrived lunchtime the next day. Once it arrived I unboxed it (a nice touch) and plugged it in - I'm happy to report that everything is up and running out of the box nicely with this one from Amazon. All the inputs are working as expected (which is more than I can say for my original one, which to begin with had zero output to display, and once I'd got that working recognised no inputs initially either!). So thank you to Amazon and the reseller Mcbazel for a great item that works as it should do, delivered the very next day at a great price! For anyone planning their own GBS-C build, I'd wholly recommend this!

Le conecté un Playstation 2 por componente, Funciona muy bien. La alternativa es comprar esos adaptadores PS2 a HDMI, pero no fue mi caso por qué eso requiere que tengas un monitor que soporte 15khz por HDMI, de lo contrario te saldrá "out of range"