Snapmaker PLA 3D Printer Filament 1.75mm 1KG Black for Most FDM 3D Printers

1. The pla get stuck pulling off the spool most of the time i have to pull it apart and unwind the spool manually so the extruder can pull it in ... So with that said i gave it a 3 star for print quality because if its stuck on the spool it does not print some layers ....

Wireframe Art'sy stuff is amazingly repeatable once you dial in your settings.. I printed the enclosed Thermal tower to find the best print temp, For my ender3 pro with a BTT SKR E3-V2.0 board upgrade. Turns out 190-195 degree produced the highest quality with NO blobbing or oozing, the finish was Awesome. I printed a retraction test also and ended up dialing back to 3mm with no Stringing. I have tried several filament's as you should too to find the one that delivers results. For Now I'm using this. Snapmaker Black PLA, The spools have a gauges on the side I find helpful also. The price when on Sale is OUTSTANDING for what a High quality level you get. $16 a 1000gm Spool pretty Cool.

Snapmakee and snapmaker filament work excellent together! This print would have taken 30+ hours on the Bambu but only took 12 hours with the Snapmaker using the dual extruder module.

Works well

This filament printed great! I found that my printer can easily print this at 205°C. The filament also adhered very well to the build plate at 60°C with a little glue stick.

i am having so much fun printing 3d models with this filament. I bought two spools, one black and one white, The black is halfway gone as I am finding things to print. I intend to buy more black and a few more colors as I am having a blast printing whatever I can.

Loaded the black pla up in my modified Ender 3 Pro and the first couple prints (100g worth) were ok. Then the filament went to crap with poor adhesion, clogging, and either was overly brittle or mushy. No change in quality with drying the filament or adjusting printer settings. Other filaments used as control continue to print fine so it's definitely the filament. Will avoid this brand in the future.

Good consistent results so far and no problems printing with this in my ender 5. I have not tried to measure for dimensional accuracy but no problems feeding it.

I bought this as I ran out of my printer's starter filament. I am not sure if this PLA is same formula or if the printer bed just needed a relevel. My 1st two prints lifted part way. After I releveled then print#3 came out properly. I suspect that now that I have it reset things should work from now on. It came in a box with vacuum sealed bag and desiccant inside the bag to absorb moisture so it was well packaged for delivery.

Twice this spool has locked up so badly it stopped extrusion. I am assuming it is due to bad winding in the factory.

Maybe I got a bad roll and the rest isn't as bad as this roll, Ill never know because I will never be buying this product again. After 3 years of printing, I have never had as many issues as I have with this roll. Its brittle, while also being soft, meaning it snaps in your hand while trying to load it into the printer, and the gears shred it instead of pushing it. After fighting and fighting with it, I finally got a "successful" print, but when I pulled it off the bed the layers separated in the print, leaving the first 4 layers attached to the bed and rest of the garbage in my hand. The half a roll that is left is now in the garbage. I highly recommend not wasting your money, pay an extra 3 bucks for a good roll. Happy printing.

Great material. Not sure why this product have lots of bad reviews. It was on black Friday sale so I picked up both colour, I have a very low end printer and once I used this filament I noticed big difference between my old filament and this. My print quality increased dramatically I'm very pleased with this material and I'm glad I didn't listen to all this bad reviews and pulled the trigger on this filament.

To be honest I find this snap maker black pla filament pretty good! The price is great. Printed this shotgun barrel 1 day 7 hrs and no clogs, Seems to blend pretty decent. ( stock hotend) 210 hotend 70 percent fan ( probably could have dropped the temp abit) and 65 for bed temp Did some test cubes with my ender 3 pro with a microswiss hotend. Works well 180 hotend 80 percent fan 65 for bed temp. Update... Ordered 4 more rolls. Put another roll on and still the same. Prints very good. Really happy with the product. Added a video of it printing.