H6054 7"x6" Chrome Housing Diamond Cut Headlights Replacement Glass H4 7x6

And bright. I swapped the bulbs for Osram Night breaker H4 bulbs but these work far better than the led lights i had previously that blinded me when it was snowing and others in regular weather. High beam lights up the road further nicely. Currently say unavailable so i hope they come back soon since I'd like another set to retrofit I had to cut the rubber cap where the bulb prongs sit so the plug was attached better, and the breather or drain tubes to fit in my headlight housing. Might not have to but my 93 GMC Sonoma did not want to sit flush in the housing without doing that. Definitely feels high quality and the black housing is a nice touch. Will buy again if they're available Put clear 3m tape or film over the housing. The glass seems thin and didn't stand up well against a random rock the other night but the light still works great! Purchasing again so i can retrofit it

I put these glass housings on my food truck to replace the old sealed beam style lights. i was going to go with a full LED replacement, but all i could find were cheap plastic lenses that would definitely scratch and fade over time. These lenses were not only very affordable, but also easy to install, and look great. only drawback is one of the reflectors inside was a little bent, possibly due to shipping, but was easy to reach in and bend it back into place. the lamps came with H4 halogens installed, but i ended up getting LED H4s. kept the halogens for a replacement on the road if needed though. overall, an awesome find, and i know these will last for years without worry.

Product: H6054 7"x6" Chrome Housing Diamond Cut Headlights Replacement Glass H4 " 7x6 (~$40) The good: Decent cut-off of light for oncoming traffic, provides a nice sideways 'Z' shaped shadow. Allows retrofitting H4 size LEDs. Rubber gasket to seal out bugs and water. The bad: rubber gasket is difficult to install. Trick is to turn it inside-out, then push it over the bulb base, then install the bulb and push gasket over the big housing. Be careful not to get finger-oil on bulb! Wear clean gloves like nitrile. Great retrofits to modernize lighting on old sealed-beam halogen vehicles and good value.

Pretty decent quality headlights for the money. They are actually made of glass and are pretty sturdy. They were a great replacement for the sealed beams that came in my car. Pair them with some led bulbs from Amazon and the visibility is great for under a hundred bucks.

I put a set of these in my 2001 Jeep Cherokee, so far they seem like they are a nice upgrade. I've always preferred the look of a more traditional headlight over the kind with a bunch of LEDs. Before I installed these I installed the K Suspension relay harness on the Jeep, which I noticed made a big difference in brightness with the Silverstar sealed beams that were in it. The Silverstars were probably the best sealed-beams I've used, but both of those quickly burned out when they got better voltage, and this setup was less expensive than buying two new Silverstars. I haven't tried the included H4 bulbs, instead I used a set of Hella halogen H4 bulbs that I've liked a lot on my other Jeep. These have a nice wide low-beam pattern with a good cutoff. I'd say it's more of an E-Code pattern instead of DOT, they angle up more on the right side of the road and illuminate road signs quite a bit. The high beam seems to be a bit wider than other H4 conversions I've used, they project pretty far down the road, but there seems to be a couple darker spots down along the bottom of the beam. These fit well in the Jeep, I did have to bend one of the interior bulb shades a little bit and they do seem a little flimsy. The front glass seems a little thin, so we'll see how long they last and if they hold up to rocks chips. Those are the only reason for 4 stars instead of 5. Overall I like them a lot and can see a lot better at night.

Perfect for keeping the oem look. Good quality, perfect fit.

Missing the turn indicator bulb or small bulb socket shown in several photos. The center reflector comes slightly bent easy to bend back with a screwdriver, with little support so they shake easily im betting they will vibrate off in time. The glass front looks good. The rubber back is not stretchy so it doesn't seal very well. Other than that I'll try to make them work.

Looks great in my 2002 duperduty