ErGear Dual Monitor Arm Gas Spring for 13”-27" Screen Full Dynamic Motion Ergonomic Design Single Monitor Mount Tilt -35°/+50° Swivel 180° Rotation 360° VESA 75/100mm Weight max 6.5KG

I finally got a new laptop capable of using two external monitors. These are pretty old monitors I had spare, LG Flatron 22" 1680x1050, but ideal for work. Two side-by-side took up way too much desk space and sat behind my laptop. I needed to elevate them.This dual monitor arm is perfect. It's a quality design and really strong. It's heavy and I was impressed as soon as I opened the box. I was particularly impressed with the clamps. In fact this is better than some I purchased to fit out an office years ago at a fraction of the cost.The instructions are basic, but easy to follow and it was installed in no time. The hardest part was getting the stands off the monitors (bad design) and I was pleased the arm came with all VESA mounting screws as I didn't have any.The gas struts are a nice touch although once adjusted I haven't found the need to move them again. My desk isn't very sturdy and the monitors can be a bit springy when I knock it, but they have never changed position. I need a new desk!If you want to push your monitors far back you'll need extra space behind the desk to accomodate the arm's "elbows".I decided the best use of monitor realestate was to turn one of them to portrait mode. I've never done this before but it's easy with this arm and makes document reading so much better. You can't really see the arm in the photo, but to get the monitors close together in this configurarion the right arm bends forward and to the left. It just shows that it's versatile in any angle and you don't have to set it up with the "V" configuration seen in the photos.I'm really happy with it and get so much desk space back.

Bought a slightly cheaper one before this and ended up returning it. Don't regret my decision. This stand is so versatile, swivels in all directions. Cable management is very easy with some velcro straps. I have a thin desk and it is holding very strong. The clamp is easy to use and you only have 2 screw at the bottom and the 8 vesa mount screws on the monitors to put in. Swivel, pan, rotate... you name it. The sping are strang and can easily be adjuster for lighter or heavier monitors. My monitors are different ( both 27 but the mount is offset ) and it was a breeze to align them at the same level. 100% recommended.

Have been using this for about 4 months now and can say its exactly what I needed. It securely attaches to the desk with a simple clamp mechanism and doesn't not budge. I have a 27inch curved screen (so on the heavy side) and the arm holds it up with ease. I'm able to turn it 90 degrees without any issue either and there's great versatility in positioning the screen. Take your time when selecting where to clamp it to the desk as it'll help with where you want your screen. The cable compartments in the arms are a little small but useful for the few cables with will never need to move. I have used cable ties on the cables I need to quickly to get out e.g. laptop charger. The cable compartments use screws, so although secure, not relatively quick to remove. I installed it solo but appreciate it'd be a lot easier as a 2 person team.

I bought this on a whim because of a special offer to replace a dual-monitor support that did not have gas springs. I am surprised at how much better this is than what I had before. You can easily make small movements to all aspects of the position of the screens and I simply couldn't do that previously - at least not without loosening and tightening screws and bolts. I now have more space beneath my monitors as I realise that they were too low before, and a better working position as well being tidier. Because of the position of my desk (hard up against a wall) it was a bit of a fiddle to get them installed but even so it only took 10 minutes to dismantle the old and set up the new. Very pleased.

I have 2x 27in Phillips panels that were wobbling a bit on their own stands and i wanted to tidy up the desk... lots of dual arm stands out there but most were too expensive. Gave this a try and wasn't expecting much but am quite impressed... well made, sturdy and although there isn't much room in the cable tidies, it's enough for power, hdmi (and you can route 2x usb cables to the base if you want to!)For around £25 it was a bargain and works well, the only thing to consider is whether you have enough space at the back of the desk to allow the arms full movement. If the desk is right up against a wall then the screens will be a good 15-20cm towards you from the back of the desk.

One of the two arms came very very loose and I can’t tighten it. other than that, really good, cable management on point and gets the job done

Quality is exactly what I was expecting, sturdy and holds both my monitors up. the only issue I got is that one of my monitors is too heavy for the swivel to adjust smoothly. It makes a horrible clunking sound and can only be adjusted to specific angles. This ISNT the products fault per say as the monitor screen is just too heavy, the Allen key adjustments wont got any higher as the instructions say but I can live with it.

Purchased to set home office and used with two 24inch monitors turned out to be really good. Gas operated arms make adjustments a breeze. Nice, sturdy design and secure fit both to surface and back of the monitor.Only complaint is a cable management system. Its fairly annoying to use - hopefully this will be addressed in next iteration. Overall well recommended.