【Pack of 20】A4 Size Laser Water Slide Decal Paper Sheets Transparent Clear DIY for Laser Printer

اشتريت أوراق الليزر بالغلط لاني طابعتي inkjet ولكن الأوراق كانت ممتازة وحصلت على نتيجة جيده بالطباعه شكرا لكم ولكن المشكله ان السعر مرتفع قليلا

am sorry to say that but its a very bad decal paper

Il supporto decal e' adeguato, provate e sembrano rispondere bene all'utilizzo.

Utilisation facile , on peut ajuster la décalcomanie quelques secondes après l'avoir posée, si on mouille la surface à recouvrir.Attention impérativement utiliser avec une couche de vernis avant de mouiller.

Inkt hecht niet goed, veeg je er van af, het plakt niet goed, rimpelt erg.

Used it for a logo on a guitar headstock and it performed perfectly: very thin, easy to use. 15-20 seconds in warm water is all it takes to separate the backing paper. Definitely recommend it for that application. Delivery was also amazingly quick (less than 20 hours!).

I am a first time user of any decal paper. I was looking for quite some time to buy some kind of paper that can transfer artwork to stretched canvas, canvas board, wood surface without losing the details of the artwork. I finally found it.I read the negative review of this product and someone said it is too thin. But because of someone mentioned it is too thin, I decide to buy it. The thin paper will make harder to transfer once it is separate after wet, but it also means the tinner it is, the final result will look less 'stuck on'.* Thin - Yes, it is very thin. But it is also strong and won't tear easily.* Transparent - It is very clear. The color of the material you are using will come through like glass.* Sticker doesn't look like plastic and it doesn't give out the glossy cheap look. It looks matted once it is applied.* Quick separation - Once the sheet is submerged in the water, it will not take long (maybe about 20 seconds) before the transparent decal paper will separate. You can actually see it start lifting from the backing paper and the decal paper start to float starting from the corner, so, no need to keep it in the water too long. Because of this reason, I found it is the best to get all material ready.* Plenty of glue backing - When I transfer the decal onto Canvas, wood, etc., I have to reposition often. Because it is thin and once the decal paper is separate from the backing sheet, it will slide around. If I am working on a small piece, it is not a big issue. But when I work on larger size, I have to take my time and reposition the decal, so it won't transfer crooked. So, a lot of glue backing helps a lot.And it does have lots of glue! It gives me plenty of the time to work without rushing through the job.* It is not the filmless decal. So, if the image is smaller than the object you are using, even though it is thin, you will still see the film when you look at them in angle. If you look at it straight, it is not easy to detect, but at an angle, you will see if it is a sticker. But, if the decal is the same size as the material you are applying to, you can't tell if it is the decal or actually prints on directly to the material.However, when I applied protective material over the decal, the edge of the decal doesn't seem that noticeable.* Laser Printer - I love the fact that it works with a laser printer. The image is burned to the paper, as it comes out of the printer, I can touch it and it can immediately put under water. ** I worked with inkjet on different image transfer method and no matter what, you can't touch the image that printed on inkjet until it is dried. And also needs to be protected with something like polyurethane before using the water.So, I personally like to work with Laser Print, rather than Ink print. I am not sure if this paper will work with Inkjet or not. I bought it for Laser printer and it works well.* End results? - See attached photos.