VFD CNC Spindle Motor Kits：220V 2.2KW CNC VFD+220V 2.2KW 4bearings 400hz 24000rpm Φ80mm Water Cooled Spindle Motor+220V 75W Water Pump+80mm Motor Clamp Mount+5m Water Pipe (Factory Direct Sales)

Works excellent, good quality VFD and spindle

The bad first. The water pump didn't work but it's not why would buy this. Just plan on buying a good quality pond pump. Otherwise it has been great. I've done several 24 hour plus cuts without a hiccup. The VFD is tied into my CNC controller so the G code commands it to start, sets the speed, and to turn off once it's done. After 24 hours the spindle is warm to the touch but not hot. It has lots of power. I use a CMT 2 3/8" surfacing bit set to 8000 rpm. It handles it without an issue. I've even used a 3" half round bit. ust add ferrite beads on the power cable for the spindle.

Great price

First, some negatives as others have mentioned...the water pump is worthless. It has a 110v cord on a 220v pump. Not the end of the world but annoying. This is just pure laziness. 1) They should have enough common sense to not advertise it with a water pump to US customers if they know 100% you are not getting a water pump. 2) No wrenches as others have stated. 3) Next to zero accurate documentation.There is a comment to not do the wiring unless you are a electrician. That is silly.Here is what I did.1) I bought this power cord. " 20FT NEMA 6-15P/6-15R Power Extension Cord for 220/240V Air-Condition,...." ... here on amazon...2) I cut the end not going to the wall off3) I bought the blue colored ring connectors from HDepot4) I hooked black and white to any two of the power connectors (can't recall the letters UVW? easy to look up). I hooked the ground to the only ground on the VFD.5) I purchased the wiring that went between the VFD and Spindle ready to go...premade from corvetteguy50 - easy to find for $230 shipping. In his video he will tell you how to hook up the wires...super simple. I put both grounds on the only ground screen on the VFD. Green from the 220 cord you purchased here on Amazon from above and one from green ring connector coming off the ground from wire purchased from corvetteguy.6) I cut the original orange water pump line in half.7) I put the original water pump screen in adapter onto the new water pump (its the right size..you will need this)8) Connected the water lines (one going to Spindle from new pump and one going from spindle into water bucket).9) I tested to make sure the water pump was flowing with no leaks.10) I programmed the VFD as shown on most videos. I only programmed 2 codes I do believe - PD005 and PD004.11). I turned it on.12) Tested a cut...completely tore up the wood.13) Spend 7 hours in the garage trying to figure out what was going on...went to bed unresolved.14) Woke up and realized the spindle was sent programmed to spin the wrong direction.15) Hit the REV button on the VFD...spindle spins correctly now and everything works great.I hope this helped someone. Figuring out how to do this...took much more time than actually doing anything. Was way easier than I thought it would be and I'm no electrician. Be careful and the above is not electrical advise...just telling you how I got this mystery thing to run. And I bought this water pump from Amazon ..."VIVOSUN 800GPH Submersible Pump(3000L/H, 24W)" - Keep the hose to pump adapter from the old pump...you will need it. And that's it. I was out the door for about $650 or so but way better than the $3500 my CNC company wanted for a 1.7KW HSD Spindle and VFD. Besides, if one part goes bad on this unit....you now know how to fix it.

Works great on my onefinity journeyman. It was initially programmed to run half the maximum rpm but it’s an easy fix. Comes with a 220v pond pump so you’ll have to buy one separately if you want to run it on 110v.