TORQUE Airbag Air Bag Suspension Kit for 2007-2021 Toyota Tundra 2WD 4WD Rear Helper Bag Spring Towing 5000 lbs (Replaces Firestone Ride Rite 2445) (TR2445)

تم تركيب على تندرا موديل 2018 جدا ممتاز في الوزن والحموله انصح فيه

Took me about 3 hours to do, do not tight anything down until the end, take your tires off and make sure you have a floor jack / hydraulic jack to lift the axle to align the airbag into the frame. On my longbox tundra i run around 7-10 PSI unloaded and about 50 psi with my 16 feet self dump trailer. Haven’t tried with my fifth wheel camper yet.

So I had one of my bump stops already missing and the other one was about to fall off anyways so I ripped it off, this made my decision much easier since these needed to be cut off anyways and I tow a 28' camper. Install was very easy but as you can see in 1st 2 pics our fuel regulator actually has 2 bolts and kit only comes with 1 but thier instructions state X2 for PCS. Contacted them and I believe they are sending 1 to me because I told them the regulator is a bit shaky with only 1 mount. I decided to put a T in so both bags are at same pressure all the time and I just ordered a Bluetooth TPM cap which are for motorcycles but will work jus fine. I gave 4 stars for now because of the missing part and also the valve stem itself is very hard to get nozzle on and off and you lose pressure fast. I ordered an inline shutoff valve which was like $8 that will help out with that. Not going to go compressor system because I found a nice little rechargeable, hand held unit that will work great not jus for the bags but all my tires too. Nice kit though, bags seem to be of nice quality but only time will tell on all the hardware especially top plates which are pretty thin and the carriage bolts when it comes to rust issues. I plan on spraying everything with rubber coating or bed liner spray. Installed on 07 Toyota Tundra 5.7L TRD Crewmax Update: contacted them about the missing fuel pressure unit missing one of the 2 brackets and they sent me all new brackets so I got and extra set of everything so TY for that. Also installed a motorcycle TPM valve cap that runs off my phone so I can keep tabs of bag pressure.... Works great!! I'm gonna give em 5 stars now. 😊

I installed these on my truck to help level the truck hauling my 29' RV. They work great and really raise the rear of the truck.

I bought the kit for my 2007 Toyota Tundra and discovered a few pieces were missing from the kit (one of the fuel control module brackets, both of the large nuts that attach the top of the airbag through the frame, and a few washers). I called Torque and explained the problem, and they immediately shipped the second bracket and a whole new set of all the nuts, bolts, washers, etc. I got it in two days! While the kit not being packed correctly was a disappointment, their great customer service made up for it. Installation was easy, and here's a tip nobody mentions on YouTube: when you cut out the old bump stops from the top of the leaf spring assembly, cut it below the level of the U- brackets but not all the way down to the leaf spring itself, you will end up hitting the nut centered on top of the leaf springs beneath the bump stop. The kit fit perfectly and the brackets for the fuel pump control module gave the perfect amount of clearance. Get the brass air nozzles on top of the airbag snug, then add another 1/4 to 1/2 turn. Make sure you cut the air line square and press into the nozzle until you hit the end, then give a gentle tug to make sure it's seated correctly. I have no leaks and the kit makes a dramatic difference (you can put your truck's butt way up in the air if that's your thing). A little air goes a long way in how it affects your ride - you will feel the difference and get the correct PSI worked out for your truck. The kit makes a nice difference in how your truck rides when it's empty and I use it along with my weight distribution hitch when I pull our trailer. It's a great product at a good price!

Nice kit. Worked well on my 2012 tundra 4x4 crewmax limited. Came with the brackets for the fuel control module. Even came with a cutter for the air line to make a nice straight cut. No problems with installation or operation.