1999-2006 (2007 Classic) Chevy Silverado GMC Sierra Fender Flares

Put these on my 2001 Chevy Silverado because of rust forming over the rear fenders. And no, there is nothing you can do about it except to either 1. Buy a new truck or 2. buy these fender flares. These are fantastic for the price. They cover the rust and make my truck look great again!PLEASE be aware though that you will have to drill holes into your fenders as these do not come pre-drilled and do not match up with the pre-drilled holes in your fenders for the factory fender covers. They come with strips of 3M tape on the inside but this will not hold them alone, or at least did not for mine. You will need to drill them into the fenders with the self drilling screws that come with the fender flares. Was not the easiest thing to do but I got it done by myself. Would be easier with two people.

I shopped around, mostly looking at OEM flares that cost in excess of $150 each to $450 each. No thanks. These are slim, clean, and really really easy to install. Took minutes aside from drilling holes. The only complaint if any is what another reviewer said; drill the holes for us. I'd add that they should include black screws instead of silver ones that I had to "Sharpie" black.

Threw these on an '05 GMC Sierra 1500 4x4 to cover my awesome rust repair. I like them. A lot.Easy to install but note that if you DO NOT want to drill holes in your wheel well flanges then these WILL NOT work for you. The adhesive tape is crap - Period.For a no-fail install, do what I did:1) Center the flare in the wheel well, ensuring the 'tabs' are lined up with the grooves on the sides of your vehicle. Use a piece of duct tape or whatever, to just help let it hang there.2) Using #8x1" stainless steel self tapping sheet metal screws and comparable stainless steel washers (the washer is to keep the screw head from going through the flare, etc). Push the center of the flare in until its flange is flush with the vehicle's fender flange and put in first screw w/washer. Check your center mark and put a screw w/washer in the the 'tab' area of the flange at the body groove of the vehicle. Repeat on other side.3) Put a screw w/washer as far down as you can access on each side.4) Put a screw w/washer between each of the screws you've already installed.5) Use a clean cloth and a little touch of Windex or rubbing alcohol and wipe as tight as you can against the flare and the vehicle; let dry and then apply a bead of clear, or black, Permatex automotive silicone from one end to the other. Dampen your finger and form a small tight bead against the top of the flare and vehicle body. This not only adheres it to the vehicle, it seals the gap and prevents not only the flare from rubbing your paint off, but it keeps rain, sleet, snow, snot, etc... from building up behind it.These are a good product for the money, they really are - just know the adhesive tape sucks and you will need to drill holes for proper attachment.Your mileage may vary.

They look nice but the stick strip did not stay on in a couple spots so it sticks out a little in some spots and I cleaned the surface.

Easy to install and they look great! Hands down a better price than the others I looked at. Wish I would have found these sooner.

These worked perfect to cover the rust over the rear wheel wells on my 1999 silverado.I took some time to cut the rust out and prime the cuts to impede the rusts return.Installation was a snap. Followed the instructions and they turned out great.Easy way to get a few more bucks out of your truck.

Fits good, looks great. But you need to make sure that the flares are aligned properly when you place the parts with the adhesive before you put in the screws. It's not that easy to take of if they are not aligned properly. The adhesive will tend to come off. But if it's all aligned in the right place, it's a breeze.

I'm not sure if the seller is paying people to write reviews or if every review writer is blind, but these are HORRIBLE. I bought them because of the good reviews. They came right out of the box wavy, flimsy and weak. Held one up to the wheel well and there has to be a 1/4" gap between the wheel well and the flare, DO NOT BUY THEM! Now I want to return them and have to pay the shipping, this is the last time I will purchase anything from Jae Enterprises Inc.