Draw-Tite 75238 Class IV Max-Frame Receiver (with 2" Square Receiver Tube Opening) , black

The installation of this product was very easy and quick, and the craftsmanship and sturdiness of this product are very good

Mounted perfectly and looks like a factory install. Hardest part is holding it if installing by yourself. If you have help, it will be a breeze. I used a magnetic pick up tool to help route the bolts and took a minute to get both through. All in all, I’m extremely happy with it

Warning these are not made 90 angles bolt holes on purpose. Looking at mine I thought this would never fit but it did just fine. Leave bolts loose so can move it around if needed. Then finish tighten. Two man on the job would make it easy. I used Hydraulic jack and blocks. Jack was too short so had to block it up. Five ***** Heavy duty more than the truck metal itself. YouTube is your friend.

Dont let the other reviews scare you away, thier fitment issues are due to them not installing it correctly.Short summary: product was shipped fast, absolutely zero damage on box or product. Install was a breeze I did it in 20 min by myself. Would definitely buy this asap. Down below I will give you Tips!!!Step 1: Take all 4 bolts and pre thread them in there designated spots (I took pics of the 4 I'm referring to). Run them in about halfway, they are hard to start, hence why you thread them in before you install!!!!Step 2: Take them back out lolStep 3: take the 2 rectangle washers and put them on the spring/wire they sent you to help install the bolts. Fish them through the hole and pull it through and get it in position. Then take the wire offStep 4: take the 2 smaller bolts and literally screw them into the spring part of the wire. Fish the bolt through the same holes as the washer. And pull the wire through the RECTANGLE washer and get the bolt to drop in the washer. (Way easier than it sounds)Step 5: take tow hitch and place it where it needs to go ( I layer on my back and held it up with my knees.Take the 4 bolts/washers that you already pre threaded and removed, and do 1 on one side and one on the other halfway. You'll be able to let go of the hutch once you have 2 bolts in on each side. Do the same with the remaining bolts.Step 6: tighten all 4 bolts almost all the way going from one to another on the other side!!! you want a little bit of play.Step 7: Take a small flathead screwdriver and put it between the hitch and the truck and hold the 2 smaller bolts you fished through in Step 4. Hold the bolt in place with the screwdriver and put on the nut. ( the screwdriver just holds the bolt so it won't rotate) tighten them all the way.Final step tighten everything down to spec.If you made it this far plz don't be alarmed. It sounds like a lot but is EXTREMELY easy. This kit has everything you need to install.

Upon receipt, numerous spots where shrink wrap and outer wrap, were inadequate, thus bare metal showing through. There were a few spots where metal was inadequately prepped, thus some paint was popping off. There were some rough spots from welding spatter, and just painted over. This is likely why it's cheaper. I will need to prep and paint the bare metal spots. Had I known this, I probably would have purchased the Curt instead. On the positive side, it is very heavy duty. I used my automotive floor jack to balance and lift it in place, taking care to align carefully, not to burr bolt threads. It installed quickly. Sidenote: Installing the wiring harness, was a real pain. Package stated : Difficult.. that's being polite. The tail light portion was no problem. The nightmare was running the power lead up to the engine compartment, taking care to keep the line away from the gas tank, as best possible. I used probably 35 zip ties to give a professional appearance.

I got this on sale for $40 couldn’t believe it but I did and it fits perfectly on my 2022 Toyota Tacoma Access Cab easy install just watch the video they have

Great value good products. It was slightly bent but wasn’t a problem bent it back into shape installed it satisfied.

Shipped in sturdy box. All needed parts and instructions included. Perfect fit. Used floor jack to lift it into place. One person job in 1/2 hour.

Unlike some other purchasers, my hitch lined up perfectly to my Tacoma frame with no issues . I fished 2 bolts through the frame with the wires provided. I was installing the hitch by myself so I used some wooden blocks to line it up & support it within about 1/2" of my frame. From there it was easy to insert & tighten all 6 bolts. Total install time was about 40 minutes with about 10 of that just getting the hitch on blocks & lined up.

Put on a 3rd gen tacoma. I did the install myself, and can say there wasn't a single thing I was disappointed with. Quality, fitment, ease were all perfect.

Great product, great fast and no hassle service. I highly recommend this product and vendor

2 holes for the back blots don't line up on 2018 Tacoma, I can only screw in the front 2 and the ones on the bottom.