Aluminum Fish Finder Mount with 1.5" / C Size Ball, Medium Arm Marine Electronic/Depth Finder Mount for Boat/Kayak/Fishing, Kayak Accessories, Compatible with Garmin, Lowrance, Humminbird

This was an update to my Ram 0.75" ball mount, which worked fine with a 7" depth finder. I updated my depth finder to a 10" screen and it wouldn't stay in place while driving. I replaced my mount with this one and not only is the ball larger, the tightening screw handle is 3 times the size and it works like it was mounted on granite. It doesn't jiggle while going wide open against the wind and yet weighs very little.

WINDFRD 2.25" Ball Fish Finder Mount, Super Load-Bearing Marine Electronic Mount, Universal Mounting Plate with 2.25 inches/D Size Ball Adapters. This WINDFRD 2.25” Ball Fish Finder Mount is a SOLID, ALL METAL (ALUMINUM), WELL-MADE Unit with the Balls made of a high-strength corrosion-resistant composite material that doesn’t weather or rust. If you are looking for HIGH quality and well-designed, this unit fulfills the requirements. It is NOT a cheap knock-off by any means. It IS Super Load-bearing, and it holds my Garmin Ultra 126sv Fish Finder and mount of 9lbs, rock solid! It has a 22lb in-motion weight capacity and a 110lb standing support weight capacity that more than covers most larger Fish Finders. It has unlimited positioning/angling and a solid mounting base. It also comes with a long arm tightening wrench that has spring detent pull-positioning to reposition the arm for super tightening to achieve maximum clamp pressure. Super cool tool! I highly recommend this unit and it is one of the best Ball Type holders I have crossed paths with. One note: On this 11” wide mount, you may have to shift some units just left or right from ‘center’ about .5” to match the mounting holes available. Other than that, I did not encounter any negatives on installation and the clamp holding strength is ROCK-SOLID! SO, I am giving this WINDFRD Fish Finder 2.25" Ball-Mount 5-STARS.

This mount is easily installed. I installed on my Bass Tracker console in the cut out for the cup holder. I used a round electrical box cover (with gasket) and it fit perfectly over the hole. It is a little cumbersome to get the nut on the bolt under the console, but using duct tape to tape it on to your wrench helps muchly. Use stainless steel with nylon bushings saves trying to hold washers and nuts at the same time. Nice sturdy mount. RAM is still top of the line, but this is a near match and works great. Mounter my Garmin ecomap 93 fish finder on it and it is plenty sturdy.

Outstanding quality. Works perfectly in my fishing kayak. I needed a mount with as much adjustment as possible, and this unit has it. Very sturdy and solid base for the finder screen. Mounting options allow me to leave the mount on the kayak. I have a modular setup and needed something I could mount below the deck so I would be able to load it into my car. This was the perfect option—incredible adjustability and extremely stable. I highly recommend it!

I needed a Ram type mount to fit the Garmin 93sv into my small Lund windshield. Recommend size was 2.25 ball. My boat stays on a small lake so I didn’t need heavy duty. I decided to try this 1.5 ball. The reviews were positive for this unit. Ordered the short arm. It’s a really solid product, nicely rubberized aluminum. I used the 4 screws from Garmin to mount to my dash. The plate holes lined up with the Garmin bracket perfectly. You need to buy 4- 8-32 x3/4 machine screws with a lock nut. I used keep lock nuts. Only minor issue is that the handle rubs the bottom of the plate when set down past 90 degrees. It is very generic looking if that matters. Haven’t quite lived with it yet, but the few times I’ve had the boat out, it’s been solid. Good buy.

Very sturdy and easy to install. Definitely recommend.

Great mount! Easy to install and holds well even in chop. I installed a Garmin Echomap UHD2 Ultra 93SV on my Grizzly 1860. I like the options the mount gives me for tilting down low while running so I can see it from the tiller. And when fishing I can stand it up so it’s easy to see and reach while fishing.

Works as designed and holds more than a fish finder. Holds my Ag Leader Monitor great!

Works great for garmin 75sv. Very sturdy in rough water holding unit in place

This fit a Hummingbird Helix7 Mega Si perfectly. All the holes lined up so no drilling needed. I haven’t had it out on the water yet but looks very sturdy!

Parfait pour sonar humminbird mega Di 9

Installé sur mon bateau avec un appareil Garmin Echomap UHD 93SV. L'installation est simple et le produit est très solide, surtout qu'il est en métal et non en plastique. Il permet de placer mon appareil à tous les angles (360 degrés) selon le besoin. L'ajustement est simple à chaque fois. C'est un must si vous avez un sondeur de plus grande taille parce qu'il reste toujours ennplace malgré les chocs et mouvements sur l'eau.

Seem very well built, equal to an original RAM mount I had for a previous fish finder. Seems well made, quality materials and does the job easily. I've made several outings in my kayak and this has securely held a Lowrance 9 inch fish finder, around 4lb of weight. The quality is excellent and i trust it to hold my expensive electonics while kayak fishing.