VViViD Black True R Carbon Fiber Vinyl Wrap Roll with Air Release Technology (3ft x 5ft)

good quality. I installed it by myself but you have to be patient. my patience has ran out because of the air bubbles were bad. I removed it several times and put it back again. Also, the adhesive is strong and hard to remove if you make a mistake. My only advice is that you should have someone to install it with and the weather is not hot because the adhesive sticks very strong. What I did with the air bubbles was to use a cutter to remove all the air bubbles so that the air inside disappears. But there should only be small holes so that the air comes out. So far the quality is good. The only problem is that the vinyl scratches easily but that's okay because I just put wax on it so that the small holes I drilled to get the bubbles out and the scratches are not obvious.

Alright, let me start with saying that this is my first time wrapping anything. I don’t even wrap gifts lol With that being said, I am completely amazed at how good this came out. Like, I really can’t believe I did this myself! I was very hesitant at first, but with a few DIY videos for tips.. I’m extremely happy with the outcome. The negative reviews here talk about the adhesive, the vinyl becoming brittle, the vinyl getting wrinkled, but literally all of that could of been fixed with a handy dandy heat gun. Even a hair dryer. Some tips I learned and wish I could’ve read here were: - CLEAN YOUR ITEM THROUGHLY A simple wipe down with a microfiber won’t do the trick. Isopropyl Alcohol or clay barring will remove contaminants that would affect how well the vinyl sticks. Especially towards the edge or where you come to a fold. - ALWAYS USE A LITTLE MORE FROM YOU NEED once you measure out how much you need, cut off an inch or two more. This will help when you come across wrinkles, air bubbles, or “fingers” (big long wrinkles you can’t squeegee out) the extra vinyl, make it easier to pull up on your vinyl to squeegee anything out. It also helps when you pull on your vinyl, it prevents possible tearing. Also it gives reassurance that you’ve cut enough to be able to wrap properly around your edges folds or creases. - A HEATGUN/HAIR DRYER IS YOUR BEST FRIEND Use minimal heat. It helps if you pre-heat your vinyl before applying it to your object. It will become soft and stretchy so that when you apply the vinyl not only will it stick better but it will also become flexible and take the shape of your object. (Like curves, lines, etc) also, when you’ve come to an edge, applying heat there will cause the vinyl to naturally fall over the edge and will stick better. Did your vinyl get brittle? Apply heat! Did your vinyl get wrinkled? Apply heat! Do you feel like you didn’t cut enough and won’t be able to wrap around the edge? Apply heat and stretch! - DONT BE SCARED TO PULL OR LIFT This is very durable material. But also don’t go to the extreme and over stretch. -KEEP A CLOSE EYE ON HOW VINY IS BEING APPLIED If an air bubble appears where you’ve just applied vinyl, it’s easier to pull back and work the bubble out, than to finish your wrapping and seeing an air bubble you missed located dead center on your object, making you basically unwrap your object halfway to get that bubble out Because you know it’ll bother you. You can use an old credit card or gift card (wrap the edge you’ll use with electrical tape to prevent scratching) or squeegee to assure the vinyl sticks to the entire surface. This also prevents air bubbles. - DONT FORGET TO POST-HEAT Once you’ve finished wrapping, apply heat to entire area you’ve wrapped. This is just as important as prepping the area you’re about to cover. Post heating will prevent the vinyl from trying to pull back and go back to its natural form. So with post heat you’ll know your wrap won’t lift or curl back. This is best with the heat gun, a hairdryer might be too weak for this one. I hope this helps! Enjoy!

This film looks and feels great. I had difficulty getting the wrap to stick around edges of trim. I believe it was a combination of inexperience and film thickness.

1st time working with wrap and it's definitely not a professional quality install....but it looks pretty darn good from a few feet away. I had to do a lot of repositioning and when all was done it was stuck down really well. I was able to work out little bubbles with the squeegee. I did crease it in a few small spots and I royally screwed up wrapping over the edge near the windshield....but otherwise it turned out pretty good. 4X5 feet of material was perfect for the hood and I had some little pieces leftover that I put on the door handles. I did use a heat gun on the edge when wrapping it around the backside, that seemed to help a little. Otherwise just scissors, a knife, and a squeegee. I used magnifying glasses for trimming the door handles and a super sharp pointy knife....kinda scary initially but after a bit putting the knife on it wasn't too bad. It cost 30 bucks and was totally worth it, how long it lasts remains to be seen but it made the car look a lot different (you see white model 3's like....everywhere right?) Might have to wrap something on the wife's car now LOL!

I've never installed vinyl wrap before. I've done my share of model airplane decals and Lego stickers, but this is different. It went really well. The stuff is an ideal thickness, in my opinion, and the carbon fiber print looks fantastic. It has a very realistic hologram effect that matches the real thing about as good as I could've hoped. It really dressed up my gaudy bike plastics well. Other reviews mentioned using a little heat for the bendy bits, and that advice is spot on. It only takes a little, though, before it becomes really soft and stretchy, so go slow. I used a heat gun on low and a few waving passes is all it needed to help me get a few ripples worked out. Where it stretches the pattern looks even more convincingly real. If you aren't working on a hot surface the adhesive is repositionable. It's a bit of a challenge to deal with the spring effect of the roll, but for smaller pieces I was able to peel it most of the way off the backing and press it back down, which served to flatten it. It's mostly the backing paper that's coiled, and flattening the roll out actually introduces ripples in the vinyl. I needed to remove those before cutting. Great product, assuming it stays stuck for a reasonable length of time. So far I'm very happy.

Update: The company was gracious enough to give me a refund I'm pretty sure this was a bad roll. This wrap is NOT supposed to be sticky but getting it off the backing was insanely hard and the moment it touched my panel it was adhered. (Thi roll at least) was NOT air release. No bubbles would come out. I could not release this from the panel at all. This is not my first wrap and I cannot believe how sticky this wrap was. The texture and design is spot on though. Looks very close to the real thing just a bummer it was so stick and unuseable.

Better than 3m 1080 and dinoc, more realistic. You really need to plan what you are wrapping to get the most out of the vinyl. If this is your first time using Vvivid's vinyl (it was my first time using their vinyl) Then you may notice that it's easy to apply and the air release technology is there. However: in some applications I feel like the adhesive is a tad weaker than 3m or oracal, not a huge deal, but it does make a difference in tight corners. This vinyl looks the most realistic at a distance and around curved surfaces. Use the tech art carbon for interiors for the most realistic look. This is great on spoilers, lips, and smaller things. I feel like the bigger the surface area, the less realistic it looks. It has a nice semi gloss coat and mild texture, unlike dinoc/1080. The carbon weave is fantastic, and definitely is high quality. This is my go to carbon vinyl for most projects. Don't hesitate to try it. It's cheaper than most of them out there.

Vvivid deleted my review on their website so I'm posting on Amazon. I can't believe the lengths this company goes to, they can't take critical feedback. This is a review for the Premium +, not XPO. Pros: Overall, Vvivid has stepped up their game from XPO. The colors have depth and sophistication. The matte metallic's have the depth of OEM car paint because of the ghost particles. The air egress technology is a lot better than XPO as well. You can push down on air bubble and gone it goes. The Premium line up can also be wrapped over parking sensors based on other reviews. On my 328i comfort access doors, I could wrap around the door handles, and the tech would work perfectly. On XPO, this couldn't happen, not sure but this might be a Vvivid exclusive? Lastly, Vvivid's vinyl is a bit more brittle making it easier to cut after you've applied. They have Avery beat there. That's where the pro's end. Where Vvivid really loses out is in the installation. It's a horrible process. The initial tack is too strong for the installer to glass out. I found myself redoing each section that I had already covered and squeegee'ed. If you watch CK Wraps on Youtube, ( a big Vvivid endorser whose probably sponsored by them) he also has this issue. You'll see him go over again and again the same spots to get glass because the tack is so strong. I also bought a tack reducer to no avail. The tack reducer works, but you are still redoing area's you've already finished. It's a frustrating process, I haven't had this experience using Avery, 3M is a bit similar, but I don't remember the tack as strong as Vvivid's. I've also never had to use a heat gun as much as I have on Vvivid's. I had Avery Dennison car previously. It went on like a dream. Pressure sensitive adhesive and far more stretch capacity than Vvivid. VVivid's carbon fiber tore when I tried glass it out (Others have reviewed the same on this very site as well). I spent around ~$400 in total to wrap my 3 series. I regret taking down the Avery Dennison vinyl as I wasted ~ 25ft on just the hood itself. Needless to say, I wouldn't recommend it. If you have lots of time on your hands and don't want to pay a premium go Vvivid. They've got good colors, but you'll stress out so much on the installation. Other professional installers in my area have said the same. I'm taking my money back to Avery. Also, after deleting my review before letting me send them my order #'s was bad form and a slap in the face to a customer. I don't see why I'd buy from them again.