GEARit Speaker Wire 14 Gauge OFC 500 Feet,UL CL3 Rated 14 Gauge Wire,Copper Wire with Polarity Mark,Audio Cable for in-Wall,Home,Car,Outdoor,Garden,Commercial Audio Systems,OFC(Black,2-Conductors)

This is pretty decent wire. All copper, none of that garbage aluminum stuff. The sheathing is tough, and this would be good for outdoor applications. The only downside is that stripping the ends cleanly can be a bit tricky, like with UF cable. I found that using the next size up on my stripping tools left just enough material to where I could score and remove the ends without damaging the strands. After I did this a few times it became much easier. Very heavy duty and good quality. Do NOT cheap out. Get this stuff.

Good wiee. Be suee to get ofc and not the cca. Much better conduction and quality. Good price too.

Great find

Overall, this is a decent product that appears to be durable and rugged enough for most applications. My intent is to use the cable for outdoor venues where it can withstand water and dirt as some portion will be buried to avoid any tripping hazard. I bought the 14 gauge, 2 wire, 250’ brown PVC sheathed cable and cut it into (2) 90 foot sections and (2) 35 foot sections to drive a speaker array. Now, here are the tips that might help when prepping this cable! When stripping the sheath only LIGHTLY SCORE it as it’s super easy to cut into the inner cable’s insulation. After scoring, just bend the cable sharply at the score and it will crack open…keep working it until it separates. (You may have to use a small set of cutters to nip the last bit open.) Make sure the wire insulation didn’t get nicked. The cable coming off the small spool is wound very tightly and has a “memory” that immediately goes back to a tight coil once it comes off the spool. No amount of “unwinding”, pulling or cursing will get it to comply as a nice relaxed and straight cable. Next tip: APPLY HEAT.. OK, so how to do that? I took each coiled length individually and placed it on a large pizza pan, set the oven to 200 degrees Fahrenheit, then put in the oven for at least one hour. Longer cable lengths like the 90 foot sections take about 1-1/2 hours as there is a considerable mass to heat. The idea is to have the heat penetrate through the outer PVC jacket and heat the wires inside to the same temperature. Wear gloves when removing the wire from the oven and lay the cable out straight. Keep the gloves on! It’s not super hot but you’ll find that the cable is quite compliant, almost rubbery, and you can readily wrap it like a regular rubber jacketed speaker wire or ready it for install it in whatever application with ease. Hope this helps!

This high quality cable was exactly what I needed. I purchased a moderately expensive low voltage lighting set that came with generic 14AWG direct burial cable. That would have been fine, but I needed to mount the transformer inside my basement, and since the cable passes into the interior of the house, it needs to pass the CL3 requirements for fire resistance. I contacted GearIT's Customer Service Department just to be sure the cable met the fire safety requirements, and also that it can be used for low voltage lighting (it's called speaker wire). The rep responded to my email immediately and cited the fire rating standards and confirmed the suitability for 12V landscape lighting and interior pass-through. She even gave me a few additional cautions about making sure I don't exceed a 15 amp load (transformer is 10 amp so I'm good on that), and also took the time to comment on my overall plan in terms of the number of cable runs and their length (which could cause voltage drop if they were too long). The cable arrived quickly and appears to be very high quality, with CL3 markings on the jacket and a small spec sheet showing the CL3 rating. Some people comment about the cable being too tightly coiled when it is removed from the spool, but I didn't encounter that issue at all. I'm really impressed with the GearIT product, and their Customer Service Department is one of the best I have ever dealt with!

This is an extremely well made speaker cable. The outer jacket is very durable but flexible, making it easy to route through and around installation obstacles. It’s also very cleanly finished, any visibly exposed sections in your installation will look professional and polished. The inner signal transfer cables are also high quality and work well with binding posts or separate banana plugs- the copper core is tight and resists fraying and splintering. I fully expect this cabling to outlast my current equipment and be installed again on future gear.

Exactly what I ordered!!!

Easy to work with

Great cable. Fast delivery. What more could you ask for?

Cavo di qualità, ideale x installazione all’ esterno

Good quality cables. Will definitely get more of these in the future.

Have not used it yet but looks great quality

Ok