POR-15 High Temperature Paint - Manifold Gray - 1 gl. - High Heat Resistant Paint - Withstands Temperatures Of 1200°F | Weather & Moisture Resistant

Did not burn off on a high temp exhaust, made the welds look great and protected them, went on easily and seems to hold up. Good quality product that worked for me. Put it on a Stainless 4 inch exhaust just after the headers and its holding up.

I have used POR coatings several times over the years. You get what you pay for and this stuff is pretty good. I have never had a failure using this expensive coating. This is no ordinary paint. This review is for the aluminum color high temperature paint. Other reviewers have complained about this paint failing to dry properly. What they missed is this compound does not cure properly until it has been baked at temperatures above 300'F for at least 10 minutes. It paints as a liquid but cures as a powder paint. It must be baked-on. After that it is quite hard and durable. It kills rust. Be careful to read the label and directions. If anything, the company should make this clearer in their labeling and how to use, mode de-employ. They do make a conventional aluminum or silver coating that air dries and does not require heat to cure. I found it elusive to find, however.

Used this paint to coat cat back exhaust system on my truck. This is some super tough paint. Exhaust looks great and paint holding up flawlessly. Be sure to properly clean and prep surface to be painted and you can expect great results from this excellent quality paint. Also have used the POR brake caliper paint with similar success.

Great product

POR-15 High Temperature Paint, High Heat Resistant Paint, Weather and Moisture Resistant POR15 advertisements used to be to the point. Seals against rust, apply to clean prepared surface, needs a top coat to prevent weather erosion. etc. I thought I was buying the same product but this one seems different, and very little information on if it is the same as the original POR15 I have used in the past. So whatever it is I bought, it went on ok, used a brush to coat some metal that was prepped and painted with POR15. It seems ok. Time will tell if it was successful. It still has the same qualities of drying hard, though in the past over time the POR15 tended to "soften" and would peel off. I didn't expect that I am assuming this is the same product and as we all apply things differently, I may have done something to cause the peeling after 10 years but going soft was not expected. I WIll RECOMMEND this with caution that you research the product well before purchase. I do not know the seller nor did I get any money or product for my random review. 240916 1103

Used this to paint the calipers on my C5. I wanted a "stock" looking gray. Not a fancy shiny silver that is available in caliper paint. This worked great, looks great and should last just as well as caliper paint since its hight heat and solvent resistant.

easy to use does as advertized

I used this to paint an Exhaust and Intake manifold on a 81 CJ5. I had to replace the manifold gaskets, so I took the opportunity to clean up and paint the manifolds. It took only 1/4 of the small 4oz can to paint the manifolds with two coats. I waited 24 hours and installed back on the jeep. There was some smoke for about 30 seconds and then manifolds were back to normal. I've put around 150 miles on the jeep since painting and the manifolds look great. I read so many posts about POR-15 being a single can use and done. If you clean the top of the can well the lid will not seize to the can. I've since reused the paint on another project and I'm down to 2 oz remaining and its as fresh as the first day I got it. Clean up and properly secure and this will last till its gone. To keep the rim of the can clean I recommend putting some blue painters tape around the seal during use and remove and clean up the top before securing the lid. I'm so comfortable that this can be reused with proper care that I plan to buy a gallon can on my next purchase.

This product worked extremely well on my fireplace insert It had old bronze louvers now the black pops out at you, this flat finish is very hard to find. Make sure you open up your windows, as does smell for a bit. Wear gloves and do not spill onto anything you don't want painted. Did require 2 coats as directed.

Very pleased with this paint. I painted my snowmobile muffler and it looks new. This paint is thick. Does not run. It's a ton thicker then spray paint. I love it but it's crazy expensive.

Followed the instructions and used the POR Rust inhibitor. Scuffed it up and gave it two coats with the POR High Temp Paint. It looks great. Make sure you use a quality brush because you could get a bit of streaking. Love it.

Followed all steps according to directions. Scuffed, cleaned & dried new exhaust. 2 coats of por15 HT, let it sit for 24hrs, install on vehicle & idle for 15 for curing. Only to have it flake off 🤦🏾‍♂️. What a waste of time. This paint maybe good for other purposes but definitely not for exhaust. What disappointment.

Super produit