ARCTIC TP-3: Premium Performance Thermal Pad, 100 x 100 x 1.0 mm, (stackable to 2.0 mm without performance loss), 1 Piece - High Performance, particularly soft, ideal gap filler, bridging gaps

Used for a PS4 pro refurb. Significantly improved temperatures. Used about half of it, so the pad itself should be big enough to refurb 2 consoles or maybe 3 GPUs. Wouldn't recommend for a modern flagship GPU but an older RTX 20 series or earlier would do fine with this. It's quite awkward to cut cleanly, you really need a sharp blade, not scissors for a good cut. It picks up fingerprints very easily and will deform or even tear under tension but besides that it works exactly as you'd expect - just cut to size and place where it's needed. Be sure to check the thickness, buy the thinnest pad that'll work for your situation, don't try to squash a thicker pad to fit a thinner gap.

Last Time I used thermal paste was back 15 years ago trying to get rid of the red ring of death on Xbox. It was messy and really hard to apply (me being a amateur thermal paste user) to cover the processor in depth and all corners covered. This pad is a game changer its literally this simple. Clean processor with alcohol carefully clean heatsink measure processor cut to fit, take of shiny protective sheet apply to processor and then proceed to take of diamond sheet this one was 1mm thick if you need bigger use two pieces. A complete novice here and this has stopped my pc from throttling this stuff works I have no problems with heat dissipation now. Also there is enough here to reapply many times the size for the price is unbelievable simply because it takes the mess away and makes it easy for novice's like me. Delivered very quick.

Used one pack of the 0.5mm, 1.5mm and 2mm pads while overhauling my RTX2080. They were all uniformly excellent quality, with the right amount of stickiness and firmness. After the overhauling (including replacing the paste with Arctic MX4) my card went from up to 98 degrees Celsius at max to 87 max (with a higher hotspot). It also took almost all of each of the three packets to replace all the pads; this almost certainly won't be needed unless you are effectively practising like I was but it gives an idea as to the amounts needed. (I did look up the thicknesses on a blueprint for my particular card and had to layer the thicknesses.....which as Arctic say is both east and effective ). Easy to install with patience and a sharp craft knife to cut them and I'm happy with the performance improvement.

Perfect and enough

Great for Xbox Series X full pad replacement. Thermal conductivity is far superior to the stock thermal putty. Pads can easily be cut to size using a craft knife and are reusable if you are careful with removal. 1.5mm is the correct thickness for Xbox series and Xbox one consoles. Great cost Vs performance. Cannot be used on the APU die itself, only for RAM, VRMs, SSD and expansion card areas. Also available on Amazon is Artic MX-6 which is great for the APU and bottles of isopropyl alcohol 99.9% for thoroughly removing the old paste/putty from all locations.

Need to be very precise. Small movements can squash it too much but overall, 4 stars.

They simply work. I was redoing the entire thermal pad and thermal paste for my ageing RTX 3060 and they simply worked. They are easy to work with, easy to place and do the job they are advertised to do.

These are really good. The pads on my 6600xt were looking really bad so needed replaced. Whilst my temps were ok before, these pads reduced them further. Idle temp and hotspot temp won't go over 32C. Intense Elden Ring sessions, (8 hours plus) and the temps are 50c and 62c respectivly. Same for other games. Always within 10c of each other. Worth the extra cost for sure. Just make sure you get the right thickness for your gpu or you risk the heatsink tilting and proper contact not being made. Your GPU maker will provide the sizes if you just ask them. XFX were very helpful. These pads are soft as well so you can be sure any gaps will be filled. 10/10.

Très bon pad thermique. Je l'utilise sur une Rx 5700 XT qui normalement chauffe beaucoup. Elle montait régulièrement à 90°C. J'ai remplacé les pads thermiques sur la VRAM, sur les VRM et remplacé la pâte thermique par un pad résultat: 77°C avec MSI Kombustor au bout de 2 heures de test. Franchement très bon pad thermique.

These thermal pads performed exactly as hoped and without a single headache along the way. I used them to service both my launch-model PS4 and a friend’s newer revision, replacing the original worn thermal pads during a full cleaning and maintenance session. Installation was straightforward. The pads were easy to work with, seated properly without fuss, and compressed nicely once the consoles were reassembled. No awkward trimming issues, no excessive rigidity, no frustrating surprises. Before the replacement, both consoles had reached that infamous stage every long-time PS4 owner knows too well, the deafening roar of overworked fans screaming under even moderate load, sounding less like gaming systems and more like exhausted jet engines preparing for takeoff. After the cleaning and thermal pad replacement, that chaos simply vanished. The fans finally returned to a whisper. Both systems now sound like they did when we first unboxed them years ago. There is very little else to say, and in this case, that is the highest compliment possible. These pads do exactly what they are meant to do, and they do it well. A good choice for anyone looking to revive an aging console without unnecessary complications.

Arctic har aldrig svikit mig förr och denna är inget undantag, grafikkortet (RTX2080) behövde nya och har fått nytt liv igen!

最近のMBに付いているM.2用ヒートシンクパッドと同じくらいの厚みです。

EWA, RYSZARD, MACIEJ CIESLA HANDEL ORGANAMI PEDOFILIA