CGM908 Picatinny Pressure Switch Cable Management Guides 8 Pack, Flashlight Laser Wire Clips - Black

Worked perfectly as described and give the setup a clean appearance. A+

Easy to install and clean looking, keeping your wires out of the way. Love these little wire hiders, have them on all my toys that have lights mounted on them.

Not bad for the price. They are made of plastic so be carful when tightening them down.

I was skeptical about these but I must say I'm impressed with how they've held up after some abuse put on the rifle over the weekend. Works as intended and easy to install and hold the pressure switch cable in place. I only needed a couple on this build so plenty left over but if needed I would buy these again.

I run a tape switch on two rifles and these are perfect for controlling the chords. Be careful though about over tightening them.

I saw these in my search for something to tidy up the cables so they wouldn’t get in the way. Saw them on another site for $60. I thought that was a bit high considering they were only a pack of 6. So I came on here to see what was available. I figured for the price and seeing as they were identical, I buy them on here.They’re not a bad idea but quality control wise, not so good. I managed to secure them on but it took some matching of parts. I don’t believe they a good quality polymer and the “threaded” screw hole were poorly tapped. Let’s see how they hold up at the range.

Liked everything about the product. Provides the ability to achieve a nice clean tight assembly. Excellent product!

*Edit - After some time with these clips, I've found that they also won't fit a B&T APC top rail without modification (you can see in the picture that the ½ with the cable mgmt would never sit flush with the rail or "bite" it as designed), also as mentioned below, the fact that the channels, which sit in the rail lugs, are so tight which causes extra "threads" to be created in them, can cause some headache since the newly "tapped" threads may not line up with the nut in the end of the clip. That said, I still like them for the rails/firearms they do fit on, & on those 1s they work great, I still think they're a great value. You get a bunch so don't be afraid to modify them to work for your application; still be cognizant to not modify them to the point that you compromise their clamping design.These cable mgmt clips are pretty snazzy. Great price, you get a lot of them, & the included hardware (screws) are quality. They weigh nothing & don't create any snag points on my carbine (along with eliminating the snag point(s) caused by my weapon light pressure pad cable). They are 1 sided, meaning only 1 side actually has the cable retention piece; the other side is just a "cap" & houses the recessed nut the screw threads into (the nuts are bonded to the plastic so they don't just fall out). So far I've used these on a Modlite & Streamlight cable & I'm sure that Surefire cables are the same diameter so no issue there, however if you try to use these on thicker cable (O-Light?), it may cause problems.Cons -The casting of the threaded side of the clip is tight & required me to assemble them before attaching them to my rail because the screw actually creates more threads in the plastic before it reaches the nut. So even after the screw cleared the threads of the metal nut (when taking them off), I still couldn't pull the 2 halves apart cause of the created threads in the plastic. Another issue I had is that these clips didn't fit my Cloud Defensive COR v2. The design of these requires specific geometry between the rail & clip in order for it to create the "pocket" that the cable will reside in. On my COR, the edge of the retention lip was making contact with the rail before the 2 halves could fully meet, & the more I tightened it, the more deformed the clip became. It would arch & bow out instead of remaining flat in the pic rail lugs.All in all, great buy, & I would trust these on any "duty" weapon.FYI, I painted a couple of mine before attaching & the tolerances are already so tight that it was difficult for them to fit on the rails; I really had to jam em in there.

I have not heard of this product before I saw it on Amazon and ordered it but it does what it's supposed to keep the wires for your tactical accessories out of the way and makes everything look professional and nice. At the same time they are absolutely not needed but if you want it to be better looking and have less chance of a snag you should order this product.

Works