DieseRC AC 110V 120V 220V 240V Wireless Remote Control Switch 433Mhz RF 10A 2CH Relay Receiver with 2 Transmitters for Garage Door Electric Curtain Motor Light DIY Radio Control Switch

If you have an application where you can easily deliver 12VDC to this device, like a wall outlet close by to plug a 12VDC power adaptor into, it's one of the best remote really modules out there. My only gripe, is that they don't make them in a 120VAC version, so I can use them where I don't have the luxury of having a 120VAC wall outlet nearby. The relays' contacts (they have 2 relays!) can switch 120VAC, but the relays' coils are rated for 12VDC. And, these modules have excellent range.I have these on all 3 of my garage door openers and on my front gate opener. I've been using them for around 5 years now, and in all that time, I've only had one failure, and even that didn't really bother me, as each of these modules contains two relays, which gives them a very wide range of possible functions, even DC motor reversing, as either relay can be set for latching, or momentary, switching. In my applications, I only use one of the 2 relays, so I was able to simply move the wires to the terminals for the 2nd relay, and I was back in business.My gate is about 1/2 a block from the nearest side street. I can be a half block from turning onto my street from that side street, and the receiver will get my signal, even from that far away. When I come around the corner, my gate is already open! That's a good 1/8 mile, or more.Also, should you lose a remote, any of the 433Mhz units, including ones with a slide down cover (to prevent accidental activation), that can be purchased right here on Amazon, can be paired with these relay receivers. Unfortunately, the maker doesn't offer any remote fobs with slide down covers. But, pairing theirs, or an aftermarket unit, is fairly straight forward, and for a product from China, the instructions better written than most!Also, they're responsive to emails requesting support. But, I first made contact with them through my orders page at Amazon. But, Amazon has now seen fit to place a virtual assistant between you and their sellers ( ¡¡¡WHICH I FIND USELESS - Boooo!!! ), so it may be difficult to obtain their email address now. If you can find a way to get past the Amazon virtual assistant, once you've contacted them through Amazon, when they respond, you'll have their email address, which is how I got it. I highly recommend these remote relay receivers and remote transmitters!!

Easy to install - good directions - works at a good distance but depends on line of sight.In my case 4 buttons on the remote control was a problem to decide what button to push in the dark. I glued a small round piece of leather (cut with a hole punch) on the correct button. Problem solved

I was hoping I could pair my MyQ to this receiver to allow me to open my old opener from the app, but it was not meant to be. It may be on the same frequency, but there seems to be no way to paid the MyQ unit to this receiver or transmitter. This unit does not seem to use Intellicode, HomeLink, or any other rolling code that can be universally programmed.That being said, I was able to connect this in parallel with my wall buttons to allow me to use these two additional remotes to open my door...the second time I connected it. Each channel has three terminals normally closed (1 and 4), ground (2 and 5), and normally open (3 and 6). I used 2 and 3 for A channel. At first I connected 1 and 2, but my wall switches didn't work.Finding a compatible programmable receiver to attach to my old opener seems to be nearly half the cost of getting a whole new opener, so I'll likely do that.

On time and the items function perfectly

The media could not be loaded. I work at a theater that hosts an annual comedy festival. I used this remote-controlled switch to build a cue light. We flash the yellow light to give the performer on stage a 2-minute warning. The red light indicates they have reached the end of their set time. Works great! No issues with range or reliability so far. I’ll update the review if any problems arise.

I have a number of the equivalent 12v operating modules all over the house and yard. I’m building a 20 button remote to seamlessly control lights and multiple audio sources that use the QIACHIP protocol.Finding these that work on 115v ac opens up new possibilities for me. I’m designing a bridge to control Insteon products that operate in the house. One of these two channel relays set to momentary mode driving an Insteon Micro-switch module will do it. The Micro-switch is not attached to a load, but can be set as a Command to activate other switches in the network. Just plug into a wall socket and setup using an ISY994. Nice solution.

solo llego uno y eran dos

Works as described. Factory mode programmed as maintained contacts. Should be programmed as momentary. But east fix to program.