ZEKOO 6FT Double Track Bypass Sliding Barn Door Hardware Kit for 2 Doors, Bypass Barn Door Track Kit, Low Ceiling, Easy Install, J Shape Hanger, Fit 36" Wide Door Panel

This is a fantastic hardware set. Worked well, is strong to hold very heavy doors and looks really good. Customer support was super helpful and responsive. Would definitely buy again.

Great product

I love the end result from the two Zekoo 6.6 ft Bypass door hardware kits that we've now installed in front of 2 closets, in a home with low ceilings. My husband and brother-in-law helped me with the time- and muscle-consuming installation of this sturdy, heavy-duty Zekoo hardware. It took us three full days, not including door staining or trips to the hardware store. None of us had previously installed any sliding doors. I've read other reviews complaining about the instructions, and here are some things that we learned that might make helpful updates to the Zekoo instruction manual: 1) The first step in the instructions should talk you through plans for the wall that will support this hardware. This Zekoo hardware is probably strongest when used on walls with a wall stud at the center of what will become the space above the doors, and additional studs on either side of the center at standard 16" intervals. My house is not so well built, with studs only at the ends of the closets. To compensate and insure our wall would support this heavy hardware, we added a 2" x 8" board to the inside surface behind the drywall above the closet. This board was supported by the top of the closet frame, and made the rest of the hole-drilling instructions work out easily. The Zekoo kit does come with drywall molly anchors. Considering the weight of the kit and my solid doors, my team decided not to trust mollies to hold it all up. We also used a 1" x 6" X 80" board, which I finished to match my doors, across the front of the top of the closet. Using this board gives more clearance for wall baseboards, and it also enabled us to make installation measurements and pilot holes on the board, before the board was installed on the wall. 2) Where the instructions tell you to draw lines, I would have said "Mark points." Once the hardware is installed, you will be able to see part of any lines you have drawn on your wall, and you may need to paint or stain over your lines. Unnecessary extra work, easily avoided. 3) The purpose of the bottom line is explained in the instructions, but the reasons for the top two lines are not. We learned that the other two lines are guides for the two screw holes in each of the brackets that will support the outside rail. These top two lines are also better replaced by marks versus lines, using a square to line them up at the proper vertical distance from the first, or bottom line of holes (see photo). The two rails ideally will run parallel to each other (otherwise, you will need doors of different lengths). Keeping everything square and using the measurements written in the instructions allows the inside and outside rails to line up properly. 4) The instructions suggest screwing together the two pieces that make up the bracket, before mounting the bracket on the wall. If you have very little clearance over the open space your doors will cover, you may have to put the brackets together first to be able to tighten the screws. I only had 8 1/2" between the top of my closets and the ceiling, though, and we found it to be much easier to mount the part of the bracket that goes against the wall first, by itself, because it is harder to screw in the wall mount screws than it is to tighten the bracket connection screws. You can then level these bracket pieces and tighten them down. Separately, in a comfortable work space, you can loosely pre-assemble the other halves of the brackets onto what will be the outside rail, lift this whole construction into place, and screw and tighten all connections. The outside half of the bracket needs to fit over the top of the wall half of the bracket, for the rails to be aligned. 5) For cutting the slot needed in the bottom of the door, the easiest approach we found was to ignore the instructions to cut out a notch 5/16" wide by 3/4" deep, and to use a circular saw set to approximately half the width of the door. My doors are 1 3/8" thick and our saw was set to cut 11/16" to cut at a depth of about 1/2". After making one cut in the door bottom, flip the same door over and, without changing the saw settings, saw again (see video). This process neatly created a straight track, which was wide enough to work with the small plastic door guides that came with my Zekoo kits. Zekoo measurements aim to have your doors 3/8" off the ground, so the guide does not have to fit completely into the track on the door. My doors slide very smoothly. We also found that the track was needed. The doors slide smoothly, but they also swing easily, without a guide. 6) You will probably need to use many washers to make sure that no parts rub together and to make the kit fit your application. We made a number of final adjustments, including using two washers on each bolt through the outside track, to keep the outside track bolt ends from rubbing the inside door bracket when it slides. Also this kit works with a range of door thicknesses. My 1 3/8" doors were on the thinner end, and the door wheel hardware includes bolts with acorn nuts, which can only be tightened so far. I needed 6 washers per bolt to make this hardware work with my doors, or 48 washers per two door closet. I bought a box of washers. 7) Finally, there are no extra nuts or bolts with this kit and there is a pile of hardware to manage. We lost much time at one point. trying to find an acorn nut that vanished. Be careful with the hardware! Other than some instruction clarification and maybe some extra washers and nuts, I think this kit is about as good as it can be, without coming completely pre-assembled. Nice job, Zekoo!

I purchased two 6-foot bipass door kits for a basement remodel. The kits sat boxed for 2 months and then I altered my design and decided on a single 12ft run with only 2, larger bipassing doors instead of 2 6ft with 4 smaller doors. I was past my return period according to Amazon and contacted the Zekoo customer service asking if I could still return the 2 6ft runs in exchange for a 12ft. Their response was swift and surprising - they informed me that I could still use my purchased hardware and that I only needed 2 plates to join the tracks into a 12ft run. They then offered to ship those pieces free of charge and said that I need not return any of the now extra pieces of hardware from the separate 6ft kits. In my experience such customer service is rare today. As for the hardware itself, it is well made and attractive. I wasn't missing any pieces from the 6-foot kits. The directions could be improved and I suggest reading through a few of the reviewer comments here with helpful suggestions on their installation experiences. Be certain that you use the correct spacer tubes for each step - I mistakingly used the wrong ones installing the first track and when it came time to do the second found that I had to remove all the screws from the first and swap them. Also, if you are remodeling, it is immensely helpful to plan on a solid header above your door frame to tap the screw hardware into. I did and it made large difference in ease and time of instillation not to have to worry about drywall anchors. All in the installation took me about 3 hours with my just above average handyman skills.

I ordered the 12 ft system for a large patio slider and hung sliding plantation shutters, and this product looks fantastic once installed and the quality is excellent. The install does take some time because there are a lot of anchors, but the product feels solid and secure. I did experience an issue with the wall anchors provided tearing up my drywall and the anchor breaking while trying to place in the wall. I ended up buying different anchors from a home improvement store. I was installing in a CMU block wall with a concrete header, and I believe the anchors provided are better suited for wood frame construction. Other than that, excellent product and highly recommend!

Great hardware kit, looks great and easy to install, rolls smoothly I was missing a stop, contacted customer service and they promptly mailed me one. They even followed up with a delivery date and followed up to confirm that I received it. Fantastic customer service that unfortunately is very rare these days. A big thank you!

Really solid product…. Easy installation and looks great

I love this barn door kit & would have given it 5 STARS BUT WE HAD SOME PROBLEMS WITH THE Plastic ANCHORS (had to replace all anchors & Screws) I called Amazon customer service because there was no customer support info from this company Amazon reached out to them and they never got back to us MINUS 1 STAR ANOTHER ISSUE IS THIS DESIGN/DIRECTIONS aren’t necessarily for this kind of bypass with a space in center so unfortunately the floor spacers aren’t going to work with these kind of doors DIRECTIONS WERE TERRIBLE Fortunately, we have installed four other barn doors, but with trial and error and a lack of directions we got them up not without some frustrations customer service support would have been helpful so MINUS 2nd STAR! we are happy with the outcome. Not happy with customer service. Or LACK THERE OF!

The Zekoo people messaged me every step of the way. Awesome product with looks GREAT

Très beau!

Material is heavy duty and hardware top quality

Metal bushings mounts for outer rail bolts don’t fit, bolts to large for bushings needed to drill them not an easy task for average homeowner as they are 3/8” diameter holes. Metal roller brackets hit at various places, this cannot be adjusted out. Some bolts required metric wrenches others were standard inch size! After communication with seller (which happens very quickly) they were very keen to help. They also asked for my input and with the mods this will be a great product for the cost. The customer support was very quick and helpful to resolve any issues.

Fait solide