KCT Nano-Texture Glass Screen Protector Compatible with Samsung Galaxy Tab S10 Ultra /S9 Ultra / S8 Ultra 14.6 Inch 2024/2023/2022, Auto-Alignment Tool, Tempered Glass

It is worth every penny!The quality is above the others. It really protects from reflections. I can use my tablet anywhere now. I am extremely happy with this screen protector. The texture is silky and made my tablet feel like a more deluxe product. It was very easy to install. Highly recommend.

Was fast and easy to do just watch the video

Fácil de instalar, viene con ayudas y las instrucciones vienen muy claras. Tener cuidado con las burbujas y tener paciencia al momento de removerlas. La herramienta para quitarlas la encontré un poco insegura al no tener una superficie suave, es un plástico duro y puede llegar a dañar el protector. Lo recomiendo a ojos cerrados y al ser vidrio refleja bastante pero en el caso de este protector es mucho menos lo que refleja. Recomendado

I looked carefully at all others for my new Tab S10 Ultra. The protector checks all of the boxes for me, and is excellent with smoothness, and anti glare. The easy installation needs improvement, as there are issues. Read on for possible tips.I set up in my bathroom which is typically the most dust free room in one's home. I used a CLEAN very large nylon cutting board as a work surface. I had read instructions, and watched the videos. I had the ceiling exhaust fan running for 15 mins, and slowly opened the door when entering so as not to put surrounding air in motion. Kept fan on.1. I cleaned the tablet thoroughly. 1st with glass cleaner on paper towels, next with 90% rubbing alcohol on PLAIN DRY baby wipes. (I use these for cleaning optics on high end telescopes and astrophotography gear).2. I used a bright LED flashlight to look for dust particles against the turned off dark tablet screen. Any strays were brushed away with a dry cotton baby wipe. I also used one of the supplied dust stickers.3. When peeling off the 1st film, keep it facing the floor, so as to help keep dust free, and peel slowly. Make sure of your orientation, and place over tablet AFTER you have checked it for dust again.4. Touch the indicated area on left to start contact with glass, and WAIT until further suction has stopped!5. Pull the RED tab SLOWLY in a slightly side to side motion, not a straight pull. WAIT until all attraction to glass has stopped!!!!In my case, a small fragment of the rubberized ribbon remained under the glass at the instant it released (see photo). I used a small CLEAN stainless steel spatula to get under the glass, then twisted gently. The glass will lift fairly easily. I used the dust removal tape to snatch it, and let the glass settle again. I had bubbles at the 4 corners, and 2 about 1 1/2 inches from the right end, above and below the horizontal center. The corner bubbles were worked out quite easily. The 2 remaining wouldn't go away. I looked with the light and a magnifying glass. They appeared as bubbles, but with a defined center point. I grabbed the spatula, and lifted the glass again. It still lifted easily. I used the dust tape sticky side up and pressing the underside of the glass slightly toward the spatula. Removed both obstructions, let the glass settle, and worked out the corner bubbles. I was dust, fragment, and bubble free! Turned out these were glass fragments embedded into the adhesive on the underside of the glass. Tells me that the manufacturing needs improvement in cleanliness. The rubberized ribbon needs improvement, it shouldn't fragment. My alignment isn't perfect. Top and both ends are perfect. Bottom edge is approx 2 mm short from being flush. FWIW, The spatula I used is the type for artists mixing paint, in my case for removing objects from my 3D printer bed. I can also recommend having a can of compressed air, such as for cleaning computers, in case it is needed. Suction cups may work as well for lifting glass. I didn't think of them until after I was done. Above all, be prepared, and take your time. This is not a 5 minute job. I spent about 45 minutes, but now have a perfect screen.

This is for a Samsung Galaxy Tab S9 Ultra 14.6" tablet. The attraction here is the matte surface, have had problems with glare with other protectors. Comes with the usual cleaning supplies and also an application frame/jig that it's snapped into. You need to exactly follow the instruction sequence to successfully get it installed, still had some dust particles get in. Properly fits the tablet. Only thing better would be a protector for the camera on the rear.First one I received came cracked, was in a sort of thin semi-padded plastic mailing envelope via USPS. Amazon replaced, had the replacement in 3 days. Shipping method was on Amazon. Main problem is the retail packaging, a thin cardboard box. Might be OK in a store coming out of a bulk case but hardly up to shipping by itself. Other screen protectors I have had came in folders with very rigid covers, extremely hard to bend. Second one made it with just a little crunching of the box corners, was sent in a paper mailing envelope with a little more padding than the first one.

Originally I purchased this item because I thought it was convenient that it came with an installation guide.I was, so wrong.It isn't just a guide, it's the first truly innovation screen protector installation SYSTEM I've seen, and I buy a lot of screen protectors.I will never buy from another company again.I am in awe.