KantoP101 Universal Projector Ceiling Mount | Solid Steel Construction | Easy to Install | Black

I don't often write reviews but this is one of those occasions when I felt compelled to do so. My requirements were for a ceiling mount with minimal drop in order to get the image as close to the ceiling as possible (I am projecting over a fireplace). It had to be unobtrusive (as it is in the lounge), easy to assemble and mount to a single ceiling joist. This mount satisfied every requirement. It is very compact and elegantly styled (as far as a ceiling mount can be). I attached the ceiling plate through the plaster board and joist using 2 x M8 Coach Screws and am satisfied that this is a solid installation (it needs to be as I sit underneath it!).To cap the whole experience, on opening the box and checking the comprehensive range of fittings, I noticed that 1 (out of very many) of the plastic spacer washers was missing (it should have had 4 of each size but only 3 of one particular size were in the pack). It made no difference to my installation because, like many projectors, mine only uses three support arms. Nevertheless, you never know what the future may bring so I emailed the company in Canada and the very same day they posted a complete set of 4 washers to me.In summary, I had looked at many different options before settling on this projector mount but couldn't find anything at this price point with such a compact, stylish and unobtrusive design - all of this supported by excellent customer service. Highly recommended.

Very well made and totally solid when installed. Flexible options including multiple fasteners. You firstly mount a plate on the ceiling with or without one or both of the supplied dropper tubes. You then mount a bracket directly to the projector (plenty of adjustments and fastener options). The bracket on the projector has a spigot protruding from it with a couple of spring loaded clips. Once mounted, holding the projector, you push the spigot into the ceiling mount until the clips latch into place (just like door latches). The spigot is attached to the projector bracket by a tensioned ball joint (adjustable) and once mounted, you position the projector by putting pressure against the ball joint in the direction required. To remove the projector is easy, you simply push it up a little to depress the latches, turn the whole projector through approx 45 degrees and withdraw gently downwards. The latches are kept depressed and don't engage, allowing removal. All in all, it's an excellent design.My only criticism is that when adjusting the position of the projector, there is quite a bit of free play before you begin to put pressure on the ball joint. This resulted in a few attempts to get the perfect position. It's not that big a deal really, as once set you'll rarely need to touch it again.

Went for this one over others as low profile - wanted it close to ceiling. Really solid construction. Loads of screws etc to fit different projectors. Suited my BenQ W2000 very well. No screws provided to fit the actual mount to the ceiling. I used Turbocoach 8mm x 60mm screws - worked perfectly. Amazing value.

Extremely pleased with this projector mount. Came with multiple sets of arms to fit any size projector and all the spacers and bolts in various sizes you could ever need.Used without the extension tube, allows mounting the projector very close to the ceiling, as was my need but the adjustable extension tube allows the projector to be mounted further away if required.Very sturdy and well made and amazed at all the fittings provided.

Great low profile however there is a wobble in the joint and I couldn't get it to stay in place. I used a few legs to resolve it.

Wanted lowest possible profile for my projector and found this one with 3", which was great. Was very easy to put together instructions were adequete. You do have to figure out how to position the arms to suit the configuration of your own projector. As its universal it has lots of options for positions / different screws and fixings. Found a configuration that worked for my projector within 2 mins of playing around. Once attached to the ceiling is very easy to attach the projector. The only issue I have had with my mount is I cant get the picture square on my screen. No matter how many ways i move it or chnage the keystone the picture just cant get square. I think i have to take the mount apart and ensure the fixings are all 100% level to make sure i get an even picture from my projector. 4 stars instead of 5 because of this. Even though its my own fault. If it was easier to get a balance on the fixings id have given 5 star

It's good, very good......but bl**dy expensive for what it is.

And it really is, sturdy, effective and 'good looking', my only gripe is the'lack of finer 'insitu' adjustment,