JB Weld 50112UK ClearWeld Quick Setting Epoxy 25ml, Clear, 25 ml

Did what it should do and easy to use.

Sets quickly as stated very strong bond ,easy mix with dual syringe. It is a bit expensive but worth it for the quick drying time. Will use and recommend this for most jobs.

Ordered to fix aluminium disc to glass table top. Did the job perfectly, but both tubes didn't come out evenly so wasted some from one tube. Would be much better if tubes were independent of each other. Quite hard to push too, but manageable. Dried nice and clear so can't see it through the glass table top.

Strong

Good stuff this. I’ve used on metal (aluminium alloy) modelling joints and for ceramics and it works fine. The key bit is to get the proportions right. They really do need to be as near 50:50 mix as you can get or it takes longer to fully cure. Once mixed it last around 5 minutes before the curing begins to make it thicken up and become increasingly difficult to use. Full curing is several hours, and I wait for at least 24 before putting it under real stress. It doesn’t cure completely clear but is fine on things such as cup handles where the joint it clean. It’s not going to show on white ceramics for example. It’s important to make sure the fit is good, and possibly a bit if support to make sure the fit is tight. Also, wipe any excess off at once as once cured it will need aggressive measures taken to remove overspill!

The epoxy glue works well and dries crystal clear as advertised - but getting equal amounts of the two parts is really difficult because the syringe dispenser is awful. I thought the syringe sounded like a good idea, and the reviews were all positive, but it didn't work out that way. On first opening and use, the clear component flowed freely but the slightly amber coloured component wouldn't come out of the syringe. I increased pressure slowly and carefully in the hope of avoiding a splurge of glue but when the amber coloured component did finally release, there was the dreaded splurge and unequal amounts of the two parts came out (I tried mixing what came out but the resultant mix wouldn't set so the amounts were clearly unequal). I tried again and this time the two parts came out of the syringe smoothly and evenly so I was able to dispense the required amount of glue which, when mixed and applied, did a very good job (although the initial set took nearer to 10 minutes than 5 and the final cure was nearer two hours than one). Unfortunately, when I tried to use to do a second small job about a week later, the same problem happened again - the amber coloured component wouldn't flow until I increased the pressure on the syringe and despite my best efforts a large amount of material splurged out and was wasted. This means that so far I've dispensed about four times as much glue as I needed and most of it was an uneven mix that had to be thrown away. I have now ordered some fast setting crystal epoxy from a well known brand that comes in the traditional two tubes which I am confident I will be able to mix accurately and without lots of waste.

Used to stick handles back on mugs made by my Grandsons. So for so good. Being clear the repairs don’t really show.

Excellent product that's very easy to use. I repaired a broken window slider on my boat to re-attach a plastic handle to the glass window.

Colle dont le packaging est espagnol, mais avec une explication en allemand. Le parquet était poussiéreux. La colle était séchée, et colle difficilement pour de lepoxy. Surtout ne pas acheter, c'est honteux de vendre un produit dans ces conditions.

I glued car headlight. I did first assembly of part with super glue and then i add this product on top. Still holding perfectly after 6 months. And he add thick layer on top. Good product…go for it.

Never buy this product

校歌速度が速く、透明でよい。 気になる点、ちょっと臭いが気になる。

It's been 24 hours and product is well mixed with equal amounts, however it's still sticky and not drying up. Label shows good expiry, but is seems the issue is bad storage or changed expiry dates. WASTE OF MONEY