Magigoo MO2016 Pen, 3D Printing, Adhesive, All-in-One

Sometimes I just can't get my parts to stay attached to the bed, especially with PETG and ABS. Even with PLA, sometimes it just doesn't happen - especially when the contact area is small. This stuff works a treat, significantly increasing the chance of good first layer adhesion. It lasts for ages because it generally only needs a thin layer to be applied once and one can do lots of prints. Over time it needs reapplying - either straight on top, or wash off previous layer with a damp cloth (water soluble). It won't completely solve ABS/PETG warping issues, but it helps a lot - the bed adhesion can be so strong that the parts themselves break (layer separation) during printing rather than coming off the bed - and that's fixable with a soldering iron. Little tip - first use requires the seal to be broken by pushing the tip down onto a hard surface until it clicks. Also make sure the tip is nicely libricated with the liquid before trying to apply, otherwise you can damage the felt and then scratch your bed.

I have been using this product for the past four months without any troubles at all. I mainly use it on the CR-10 with PLA and PETG and had no problems with adhesion. In fact the part sticks well on a hot bed during printing and then can be literally picked up from the bed after everything cools down, just like magic. I also use it on a Wanhao replicator 4s with ABS and I have had no problems with warping, as long as the bed was correctly leveled. Application is easy, I just followed the instructions, pushed the tip on the bed, I think there is some sort of bead in the tip which lets the magigoo flow out in a consistent manner. On the first time I squeezed the bottle a bit too hard and a little too much magigoo came out but I spread it evenly on the bed and printed with no problems, so one should avoid squeezing the bottle with a lot of force as it will probably make a mess. However this is not such a problem as the product can be literally wiped away with a wet cloth. Overall I would say that I am very happy with this product since I can print directly on glass with no hassle at all, I just apply, print, wait for everything to cool and take off the print. I also like that the product came with clear instructions on how to use.

I have been using this product for several months now and all in all am pleased. I print in PLA and PETG. At the risk of sounding critical, I would not describe this product as "Magic" (as in Magigoo) as that implies it would work irrespective of anything that I might (or might not) do. It certainly doesn't "just" work and requires some effort to get good results. However, *everything* in 3D printing requires effort (experimentation) and nothing "just" works. The three things that seem to ensure success for me are: 1) Print head<->print surface gap. I seem to need a slightly smaller gap than I do with other print surfaces to ensure good adhesion. For example generally printing 0.2mm layers (with a 0.4mm nozzle) I find that a 0.18mm gap works best; printing 0.08mm and a 0.05mm gap works best. 2) Print surface cleanliness - I print onto a borosilicate glass sheet. According to the manual you only need a damp cloth to clean off the magigoo residue. It certainly does wash away with water but I found that unless the surface (glass sheet) was very clean then I got adhesion failures. I clean the glass-sheet with soap and water and dry thoroughly before re-applying magigoo. 3) Bed temperature - magigoo needs some form of heated bed to activate the <cough> "magic" but how much really varies with the material being printed and even the layer height! I found more variability in adhesion results depending on temperature than with other surfaces (e.g. PEI sheet). For example: printing PETG @ 0.2mm layer height and bed temperate needs to be 85C but printing at 0.08mm layer height and I need to increase bed temperature to 95C; printing Rigid Ink PLA and I can get away with a 40C bed temperature irrespective of layer-height! Basically, you need to experiment to find the best settings for your rig but once you do then it should give reliable and consistent results. The key questions: Would I buy this product again? Absolutely yes. Would I recommend this product to someone else? Yes (bearing in mind the need to experiment).

I wouldn't bother using this every time with something like PLA, just try increasing your bed temperatures.. For Nylon however, this stuff has been a godsend. I use the Bambu Lab X1 Carbon with the high temp plate, which is a smooth plate. Most of the time my nylon prints perfectly fine, but sometimes I experienced warping which ruined particular parts or the whole print. With this product, I've not had a single Nylon part warp on me yet, it knocks the pants off of a normal glue stick, it's super easy to apply to your bed and dries in to a very thin layer on your build sheet. I've had to take a star off here because the claim you can reuse one application multiple times is simply not true (at least not for me). Once the parts release from the plate, the layer of the product comes off with it, leaving a patch of untreated bed. I did a test of this, applied the product over the entire bed, then did a first layer test with nylon - stuck perfectly, once removed you'll notice a colour change on the build plate (back to its normal colour). Printing the same test again I experienced adhesion issues. In short, don't expect this small bottle to last overly long, but for me it's worth it. It's expensive for what it is, but if having perfect parts is key for you, then it may be worth that extra cost.

I was skeptical when I ordered this product. "Is it just a big expensive pritt-stick?", I thought. Having used the product, now I'm a believer. I'm using it to print PLA onto a glass surface. The first layer sticks very well, with no smearing or dragging of the first layer. Mission accomplished! However I then discovered the product has a second benefit which I didn't anticipate: once my heated bed cools down the print separates from the bed effortlessly. I can retire the putty knife I used previously to pry prints off the bed! So basically it's all brilliant on that front. The magigoo seems to remain on the glass, it doesn't transfer to the printed part as glue stick sometimes does, I've done about dozen prints without any need to re-coat the bed. Hopefully as long as I store the product properly (in the dark, it seems) it will last me a long time. I've only tried printing PLA so far. I'm going to try experimenting with PETG next. The only downside to the product is that if you have an uneven coating on magigoo a glass bed, which is what I ended up with having used the applicator they supply it in, any ripples or texture in the coating are transferred onto the printed part. If the bottom surface of the part will be on display this leaves an uneven pattern reflective/matt texture on that surface of the part. The best solution I have found so far is to lightly sand the surface with 1000, 1500 and then 2000 grit sandpaper after printing to give an evenly matt texture. Overall I think this stuff is great, not having to worry about adhesion or removing the print from the bed has made printing much more fun and practical. I bought this concerned that it wouldn't prove good value for money -- I'm pleased to report that I was wrong!

The best solution for ABS I have found in 12 years of printing. Applies easily, no odour. Just shake and wipe on as you would a glue stick. I`m now using it with a Bambu P1S with the supplied textured sheet and have used ABS filaments from Elegoo, Creality and SteadyTech. Bed temp 90, nozzle temp 240-260, standard fan settings ie. just generic abs settings from Bambu. In over 200 prints I have not had 1 lift, simply amazing, I cannot recommend this enough.

Great product. The usual problems that I have had were that the filament first layer stuck OK to glass bed using 3DLAC but when I removed the model it ripped the first printed layer off. See attached picture. Also models had to be chiselled off and then the glass bed cleaned off and the laquer re-applied. No such problems with Magigoo. You must allow the glass to cool then the model just pulls off with no effort or damage. The attached video was taken after two previous model prints had been done in exactly the same place and the original Magigoo coating still in place. Not sure how many can be done before cleaning off (with just water) and re-applying but I suspect quite a few. Note you MUST allow the bed to cool before removing the model. Also care should be taken to get a nice even Magigoo layer with no bubles etc. My layer was a bit sloppy as I did it in a rush but as you can see it still worked perfectly. This product is a great solution to a usually troublesome problem. Great stuff.

I was having problems printing tall items using ASA filament on a Bambu Labs P1S with textured PIE plate, they would come unstuckbefore the print was finished. I thought about changing the plate, but after reading positive reviews about using glue I decided to give it a go. I've not had any issues with adhesion or warping since using it with ASA, PLA+ and PETG. No need to buy another plate now 😊

Quality is good

Magigooは凄い。 よく張り付いて、モデルが歪みません。

Ich war ein wenig verzweifelt. Ich habe den Artillery Sidewinder X1 V5, der ja schon von Haus aus ein sehr gut haftendes Druckbett hat. Ich habe mich vor etwa einer Woche an das Drucken von ASA herangewagt. Da ich (Noch) keinen gekapselten Bauraum habe, hatte ich mich schon auf Haftungsprobleme eingestellt. Und so war es dann auch. alles was höher als 10mm war löste sich früher oder später von der Platte. Dann habe ich diesen Klebestift bestellt... zu verwenden ist er etwa so wie ein normaler Klebestift die Konsistenz ist bei kalter Druckplatte etwas dicker als Wasser. so kann der Kleber schön in alle Unebenheiten der Druckplatte fließen. sobald ich dann die Platte heize fängt der Kleber an zu kleben. nach dem Druck bekomme ich gedruckte ASA-Teile nun nicht mehr von der noch warmen platte gelöst, vorher lagen die Teile halt mehr oder weniger auf der Platte. sobald die Platte abkühlt hört man schon wie sich die Teile selbst lösen (knackt und knistert). anschließend nehme ich ein stück Nasse Küchenrolle und reibe kurz über die Platte. Der Kleber ist Wasserlöslich, daher ist die Druckplatte danach blitzsauber. das entfetten mit Spiritus lasse ich mir aber trotzdem nicht nehmen. leider finde ich 18€ etwas viel, aber verkraftbar. zudem weiß ich auch noch nicht wie ergiebig so ein Stick ist. Alles in allem klare Kaufempfehlung von mir. ich werde gar nicht erst irgendwas anderes auprobieren, da diese Anwendung sehr einfach ist und ich hinterher kein geschmiere habe.

A must have for your 3D printer

Doesn’t hold my larger ABS prints.