M3 Small Screw Kit, Short Wood Screws Assortment Kit, 600pcs Tiny Screws 6/8/10/12mm Phillips Flat Head Self Tapping Electronic Accessories Screw Multifunctional DIY Micro Woodworking Small Screws Set

These screws aren’t for building a house! They are small and do the job they are meant to. Look at the sizes and not the pictures before buying. They also do not use a #2 screw driver.I personally use them while building acrylic cases for PCB boards. After drilling out a pilot hole they screw in just fine.If you put the driver in squarely and have a pilot hole then they will work just fine for any LITTLE jobs you might have. I would buy again!

Purchased both stainless & black versions of these M3 screws and found them both to be excellent. Intended purpose, to attach hardwood trim to cabinetry with hardwood facing (all cherry), in some areas mounting the trim onto the plywood used in the cabinet boxes. Intention was to have no screws visible so screws were inserted from 'back" so either through the cabinet facings or the plywood.Cut to the chase, what worked really well for me...TL:DRDrill full 3/32" pilot holes, then 1/8"clearance the holes in "through" material, and 1/4" countersink in hard materials. While "full-size" 18V impact wrench or screwdriver are ok for pilot & clearance, use a small (typical 5V rechargeable) screwdriver for deburring and countersink, and with clutch on lowest or near lowest setting and new quality #2 Philips bits for screwdriving.TL: maybe read anyway!Typically using clamps so drilling multiple holes would align:1. Drill pilot hole(s) through cabinet facing/base material into the trim pieces, to a depth at least the full length of screw, with a 3/32-inch bit. Complete all holes before removing clamps.2. Separate pieces and clean up the holes on the facing surfaces ("touch" holes with 1/4-in cross-hole countersink (c/s) deburring bit).3. On the surface where the screws are inserted, drill through all holes with 1/8-inch bit for clearance.4. On the plywood or hardwood surface where the screw will be inserted:—with plywood deburr if needed (explained in 5 below)—with hardwood, use the same cross-hole c/s bit to create full c/s (go deep enough the whole bit cone portion is completely flush with wood)5. Using a small 5V-type rechargeable screwdriver with a new Philips #2 bit and the clutch set on LOWEST setting*, use firm pressure and drive all the screws in until the clutch rattles. If any screws not fully set, increase clutch setting a click and try again. In plywood, the head will pull in flush or below without prior c/s.I used about 60 screws for this project, and for some parts repeated installation and removal was required. In all only 5–7 screws were tossed after this repeated use rounded the heads, most often as I didn't get a square shot because of awkward locations, and in one case the pilot wasn't drilled deep enough. I never snapped any, or rounded one out enough to require vice grips, using this approach. Where they are visible (black ones into black aluminum supports), they look great.

I am disappointed in myself that I was mostly focused on the variety of lengths of these screws, unfortunately I didn’t notice that the heads are all the same tiny size. This makes them less versatile and useful than hoped.

One of the first few screws had a head that sheared off while screwing in. Was a POA and decided to leave it in the material since it was too hard and annoying to remove. But the screws are otherwise as described. it's a good kit with a nice selection of lengths but be mindful of using it on hard materials or at awkward angles.

These are perfect screws for any inside rv fix. From usb ports, to cabinet doors, these did the trick. Solid buy!

On the plus side, they look nice.In fairness, these are only M3, so the limit on their strength is low. Even still, I have found them essentially useless for any length longer than 8mm. I have only use them in wood for simple mounting and always with a bore hole. 3 out of 4 end up stripping out the Phillips head -being 3mm stripping is instant and complete when it occurs- when hand driven with careful head size selection and deliberate force. I have then tried to remove the screw using hand pliers. Once I succeeded removing the screw in its entirety. Several other times the head of the screw tore off leaving me to attempt backing the screw shaft out, again with hand pliers, Backing the shaft out ended up simply tearing the shaft in half. Twice I gave up backing out and simply drilled out the screw. Bear in mind, except drilling out the screw remnants, every thing was done using normal hand tools, driven by hand, inserting and removing the screws into spec'ed pilot bores (by size and material).If you have very soft material -balsa, cardboard, low infill PLS/PETG prints, and are using these screws where you can ensure exact and perfect alignment of tool, pilot, and screw at every moment while also able to provide overlength pilot holes then they may work for you. I'd recommend avoiding them completely. They are exceptionally weak.

It’s a good set but needed longer for the audio box but I’ll find good use for them thanks and delivery was fast and they are worth it

I bought these to repair my musical instrument and they worked perfectly!!

Good screws

These black screws are great, love the fact that they are black so they go really well with my black furniture and shelving.They are fit for purpose and I haven’t had any problems with them. Always handy to have a small set with plugs that’s easily carried around to do jobs around the house.Recommended.

Good quality wood screws with a good bite. Lots of sizes

We have a black and white theme in our house so these have been perfect for when screwing to the wall. They show up less and look neater I find

The media could not be loaded.  This is very handy when you want to build something and has pretty much every size that u might want or need.Good value of money and very useful in the house .