Redbat Monitor and Laptop Mount Stand, Fully Adjustable Monitor Arm with Vented Tray for 13" to 32" LCD Screens and Notebook up to 16", Holds up to 22lbs, VESA Compatible, Dual Mounting Options

It's definitely my fault for having that excitement go through the roof when this arm arrived. While I could understand most of the manual, I skipped the part where there's a pair of squared metallic parts that hold the two arms to the middle tube. I twisted those screws with all my strength, bending the pieces in the process until I noticed those two pairs of plastic pieces that go inside those metallic pieces. While I check the manual again, there's this part where they show how they go, but it's so tiny that I missed it entirely, and went my own way, even asking myself why do I need to screw these parts that tightly? It didn't feel right until well... I noticed. But after all of that, man... My desk improved a ton. I couldn't be happier. Sure, I don't have the up and down adjustment I could get on more expensive stands (though, manually, you can move the arms on the tube by using the screws to loosen and move the arms). But the fact that now I can put my monitor on vertical, tilt my laptop screen, and use my desk like if it were a standing desk is just perfection. Cable management is relatively easy, and the pack includes a ton of screws, the Allen keys, and two ways to install it (clamp or a screw under the desk if yours have a hole). So yeah, read the manual. You should also make sure to point the screws away from the monitors since if those metallic parts I bent have their screws on the front as I show in one of the pics, you could easily scratch or even damage the monitor you put on the arms (because yes, if you don't want to use a laptop and instead put a 2nd monitor, that whole laptop stand is supported by a VESA mount. But again, be careful with those screws in any case. Also, if only these manufacturers allow you to buy just the arm and not the entire thing to add, I don't know, a third arm in the future...). The thing is really tough though, and you can adjust how much you allow the parts to move by tightening every screw you need so, the possibility of a laptop or a monitor on the arm moving on their own is only if you allow it (the best part vs. the gas ones, even with all their benefits). As an entry-level stand for anyone doing home office, I recommend it. For me, it's worth it.

I wanted a way to use my laptop at the CNC machine and this one looked like it would do the job. And it does! I was concerned about the stability of it but found that it has all the stability it needs. It’s made to swing to a different position if needed. The clamp mechanism attaching it to the table has been set initially and has not been touched since. There are really no negative aspects about it. It was easy to assemble and mount to the table, easily adjusted, gave my laptop a secure spot that is both convenient and out of the way. I recommend it for your CNC table.

This is not a bad computer and laptop stand to used. The simple setup to the durability of this stand is well deserves. Since all the parts are made out of metal, it can withstand the weight of a 37' monitor and a 27' laptop. The bad thing about this is just the fact that tightening the bolt and screw take some effort. Also, the part that bend the back and forth needs some redoing as it is still difficult to fix the position of the monitors and laptop.

I bought a similar desk mount for my screen and laptop, then bought this one so I could do something similar with my keyboard and mouse for a movable setup. So I don't even use this for a laptop. It works pretty well for this purpose and I think it is priced fairly. For what it is it probably should be a few dollars cheaper but it is worth buying if this is something you need. The entire thing feels durable and should last a long time. Putting it together is a chore, as these desk mounts are always a bit awkward but the set up isn't anything too crazy. I got it done while watching TV and all I needed were the included Allen keys, as you can hand tighten everything else though you should follow up on the Philips screws with a drill or a screwdriver at some point. As the instructions are a little iffy I would rate the assembly on this at a difficulty level of say 3-4/10. Not hard, just annoying. Just be prepared for that when you get it. Otherwise I feel pretty satisfied with the item.

I’ve only had it for about a week and it is an excellent product. Very sturdy material I thought it possibly could be too heavy for my desk, but was perfect. I like how you can adjust the height of the arms if needed and to bring the screens forward or back if needed I don’t move the arm as much, but they don’t touch my wall so no damage there. It does come with screws monitor, but I just use the screws that came with the monitor which is a 20 inch Dell monitornot sure what size those are. Recommended especially for those who work from home.

I purchased strictly to use as a moving lap top holder and used half the second arm as an extension, and the the other half with the end that would attach to a monitor as a support for the extra length, and weight of a large laptop and big hands , I'm 6'6" and have had back issues for years so I work from home and create - and recreate my workstation to fit and fit comfortably based on having to replace comfortable chairs, as office desks do not fit folks over 6'4' nor do the chairs - and even the stand up desks were always too short, and jobs these days the need to write anything comes less and less so I have very little need for a place to write or lay a full sheet of paper on, so I literally either work in an over sized high arm living room type chair or a recliner with a long coffee table between them that drilled a hole in and installed this contraption on so my workstation can swing to either chair. and it works pretty slick - If I were to be picky I would say the joints could be built a bit stronger but I'm not using it properly - and for the price it's legit. .... Also I think if they sold individual parts out of the kit it would also benefit them, I'll probably be ordering another one for replacement parts to have available when the hinge pieces get too bent and loose from being used improperly. I'm happy with it .. comfy work means productive work!

Well built, not easy to assemble. Parts come with letters in the instructions, but are not labeled themselves. It will work, but will not work with desks that have a tube frame, you need about 3" or a completely flat bottom desk so this can grip and hold. I had to modify my desk so this would fit and work with what I have. There isn't enough information or pictures so you can know exactly what you're getting into. The top shoe or bracket has a foam stick-on pad so you don't damage your desktop, but the bottom clamp does not and it is steel, so if you have a glass desk, keep that in mind. Overall, works but could be a whole lot better.

This attachable computer and monitor stand is exactly what I needed! It clips securely onto the small mobile desk I purchased, creating a compact and efficient workstation. Assembly was quick and easy, and setting it up took just a few minutes. My 17" laptop and 17" travel monitor fit perfectly on the stand. The monitor has four screw holes that made attaching it simple and stable. One of the best features is how the stand positions my screens at eye level, whether I’m sitting or standing. No more neck strain from looking down! When I’m done for the day, I can fold up my desk with everything still attached and store it out of the way. It’s a game-changer for small spaces

Commandé pour faire de la place sur le bureau et pour pouvoir orienter l’écran ! Je me demande comment j’ai fait pour travailler avant. Qualité au top tien bien tout est compris même les clés ! Un écran de 27 pouces et mon portable de 16 pouces sont maintenant au même niveau c’est impeccable pour travailler.

Funkar hur bra som helst! Stabilt och lätt att montera

Très bon produit, solide. Facile à monter, je recommande

Redbat Supporto Monitor Braccio Display Il supporto monitor Redbat si è rivelato un prodotto eccellente per ottimizzare lo spazio di lavoro, migliorando al contempo l’ergonomia. Qualità dei Materiali La struttura in metallo è robusta e stabile, garantendo un supporto sicuro anche per monitor più pesanti. Le giunture sono ben progettate e resistenti, senza alcun segno di cedimento durante l’uso. Facilità di Montaggio Il montaggio è semplice e veloce grazie alle istruzioni dettagliate e ai componenti inclusi nella confezione. L’installazione non richiede attrezzi particolari, e il sistema di fissaggio alla scrivania è solido. Funzionalità Il braccio è completamente regolabile, permettendo di inclinare, ruotare e alzare il monitor in diverse posizioni. Questa versatilità consente di adattarsi a qualsiasi configurazione di lavoro, migliorando la postura e riducendo l’affaticamento visivo e cervicale. Pro e Contro Pro: • Materiali di alta qualità e struttura stabile. • Facilità di montaggio e installazione. • Regolazioni multiple per una maggiore ergonomia. • Ottimo rapporto qualità-prezzo. Contro: • Non adatto per scrivanie molto sottili. • Le istruzioni potrebbero includere ulteriori suggerimenti per configurazioni avanzate. Conclusione Il Redbat Supporto Monitor Braccio Display è una soluzione ideale per chi desidera un setup di lavoro ergonomico e ben organizzato. La qualità dei materiali e la facilità d’uso lo rendono un ottimo acquisto, adatto sia per uso professionale che domestico. Valutazione finale: 4.5/5

I wanted a floating adjustable keyboard stand and couldn’t find anything suitable for my desk setup. I saw this and although meant for a screen, it works amazingly for my purpose. Quality product and very sturdy. Easy to put together and as I found out, very adaptable. Simple and smooth to adjust. Great find! 10/10 👌