NZXT F360 RGB Core | 360mm Single-Frame Fan Unit with 3 x 120mm RGB Fans | Speed & Lighting Control | High Static Pressure & Airflow | Fluid Dynamic Bearings | 8 ARGB LEDs Per Fan | Black

I have no complaints with these fans. I’ve been an nzxt fan for the longest because nzxt’s software is easily accessible to control my fans. Installation is fairly straightforward, I Love them

Came fast and super easy to install LOVE THEM (also I fixed my mistake and changed the way my bottom fans faced lol) 😂

looks good, comes with adapter. easy to install, only 1 set of cables

Works great

Need a pcie cable from your power supply to the fan controller if you want to control these with the nzxt cam software. That is some diabolical engineering on their end. Whats also a menacing act on their end is releasing these fans without the new controller. These should have shipped with the controller and it shouldn’t be $50. Anyways, Why not just make it connect with two sata power cables instead of a pcie cable? Like every other controller I’ve used.the light bar on the side is not controllable. It runs off of the fan light. It is not separate. However, these are the cleanest looking fans I’ve seen and it pairs well with the new kraken. I only need one software open on startup now. I used to have Lian li Infinity fans. On paper, these perform slightly better and don’t look too “gamery”. Infinity fans look very gamey but every 3 pack of those comes with a controller included.Additionally, the cables that connect to the fans are not removable so if a cable stops working then the entire fan system will not work for that set of fans. A cable is less expensive than 3 fans. I don’t know why they designed it like this. There is a 5 year nzxt warranty for these fans though so I’m not too worried.The last issue I have with them is the led hotspots. Meaning, you can visibly see the leds around the fans when configured as exhaust. Also, it is not a warm white. It is more of a cool white making it look blue. See the color difference in the photos I added. EDIT:After googling it, if you add yellow to cool white, it makes it warm white. I’ve added my color profile to the photos so you can see the before and after. The base white color will look blue, you actually have to add yellow to the color hue in CAM for it to look as what I would consider a normal white.On the upside, only needing 4 screws for three fans makes it too easy to install which is a really nice design. normal 3 packs of fans require 12 screws.They are not very loud. I run them in the silent sound profile and the sound is never noticeable. If it is too loud, you can change the fan curve in CAM. Some people have said that tightening the screws into the fan too hard can cause a hum or a buzz sound.These are the best nzxt fans you can get but there’s better fans available without these flaws ex., Lian li and Corsair have “all in one” fans that are way better but also more expensive. But if you want to stay in the nzxt ecosystem then these are decent. By no means are they bad, but again, there’s better fans out there. These are about a 3.5/5 because of the obvious flaws.

I know nothing about these other than my son needed them for his PC and he said they work great. He had a smaller fan in there that was not keeping up and after a talking these, he has had no issues!

Accidentally ordered 4 more than I actually needed. Won’t be sending back though. These are really nice. Fit my case perfectly. Nice colors and really good flow. 5/5 would recommend.

I'm a first-time PC builder and I didn't need anything fancy for a back panel intake fan, but I wanted to sync RGB with the H6 Flow built-in fans and two Lian Li infinity fans. I couldn't figure out why my RGB was not connecting properly or why the colors were off (I'd set the case to purple and this fan would stay red, etc). I had each set of fans plugged into a different RGB/rainbow RGB header in my mobo and this was the only one with issues. I finally figured out that it's because NZXT wants you to buy the controller and this fan is specifically not designed to attach directly to the mobo. My other two sets of fans connect perfectly as-is, so it's really disappointing that this fan is the exception. I'm going to see if it's possible to add it to the daisychain, but I'll likely end up just putting it on the 4 pin RGB header and not sync it to the other fans.