LED Strip Extension Wire Cable Kit-AWSOM LED Strip Wire Solderless LED Connectors 4Pin 10mm for 5050 RGB LED Strip Lights

Easy to recomend. The price was right. The shipping was fast (prime). It solved the problem. The extension wire to LED strip clips were what I needed to solve my problem with poor soldering skills. I will say, however, that they were not completely ID10t proof. It took 2 tries to figure out that it was easiest to use with the circuit live; opposed to build on the bench and relocate to the installation site. Open the securing clips wide, separate the exrension wire about 3/4" press each wire in its groove with thumb then press down the holding clip. Then, the LED strip. Cut on the cut line, do not remove waterproofing, open the holding clip to see the conductor pins well, line up the strip - this is where a live curcuit helps..put the contoller on white (all colors on. When you get all colors lighting up, press down the hold down clip. Note: a bad connection on the extension wire side can also be the cause of 1 or all colors not working. Be patient. Be ready to open and try again. Have fun! I did not try the adhesive backed mount clips in my application. I did not use this outdoors or in a wet location. I only got the wather proof variety to match my existing LED stips. Wife loves her new indirect lighting on her knickknack shelves.

I purchased this to fabricate a few jumpers so I can string LED lights through the kitchen (on top of the cabinets). Unfortunately, I am starting with one set of Waterproof lights and two sets of indoor lights. The waterproof set has a very thick coating of plastic covering the lights, the other ones do not have this thick coating. I find that the wire to LED strip connectors do not work if you are using the non-waterproof strip, the contacts just will not penetrate to make contact with the LED strip. I am going to try building up the thickness locally using electricians tape, if that doesn't work, I will have to get a thin soldering iron (unfortunately all of my soldering equipment is too large for this application). I suspect that the waterproof strand will connect much easier (as you can see in some of the videos associated with this product). The wire ribbon is 22 gauge, so relatively thin wire - but the wire splice terminations work quite well... I am sure someone could come-up with a more reliable termination gadget, will keep my eye open, but once I get these wired, I doubt I will have to worry about re-terminating any of these.

Review edit... After completing my LED tv project with these parts. Wife gave 2 thumbs up. So im adding 2 additional STARS. Originally only 2 STARS because 4 of the connection pieces are missing. Other than that I properly received all sticky hanging clips and the strong looking wire. I'm excited to get my project going. Using remaining wire and pieces to compete car LED strips project.

This kit was used to mount light strips under kitchen cabinets. The connectors that connect the light strip to the wire do not securely connect or clamp down on the light strip causing a poor or no connection at all. I’ve had to adjust the connector several times to get a secure connection. Several times so far sections of the light strips will turn off due to the connector not lining up properly with the light strip. May work good with certain light strips but definitely not all.

Perfect for under cabinet light. Love the RF remote. Easy to install if you are a little handy soldering.

The wire is fine, and you shouldn’t have to strip it back due to clips it comes with but here’s that part. The clips are absolute trash, and a waste of money, I could have bought 20 gauge wire at Home Depot and been fine without this product. Stripping the wire even at the 18 gauge mark on my wire strippers still would pull strands of wire off... Here’s what you do, but 4 stack multicolor wire at a local hardware or electronics store, and buy a soldering gun. You tube how to solder and teach yourself. It’s the only way to ensure a constant and permanent connections. These clips wasted so much time and it got to the point that playing with them for connectivity became pointless, the lights are going in a camper and if just touching them messed up full connectivity then they would stand a chance in transit. Realistically they aren’t even good in a kitchen or behind a tv, at their best I had to pinch them to get them to connect. Don’t waste your money on this kit, it truest isn’t worth it

Perfect for my led project.

Fast Delivery, work good, will purchace from them again

As usual the items arrived on time. The quality of the wire is great ,the clips are easy to use. This is a 5 for me

It looks fine will know better when I start using the wire for LED projects.

The connectors don't work even if I pre strip the wire and put the metal tabs directly on the led strip. This is useless, would give 0 stars if I could

Tried using the waterproof connectors without luck. Resorted to using the non-waterproof connectors.

Worked well for my job