Google Pixel 3 Screen Protector, Vigeer [0.3mm, 2.5D] [Bubble-Free] [9H Hardness] [Easy Installation] [HD Clear] Tempered Glass Screen Protector for Google Pixel 3 (Clear)

I had previously bought the Biuzko screen protector, but couldn't find one for the Pixel 3 yet so I tried this. None of the instructions match each other, or what comes in the box. It says there are 2 layers of protection (front and back), but there was only a tab to pull off the sticky side protection. There are visible marks under the screen, not sure if it's from the glue, but they're not air bubbles, just streaky bits (?). It feels hardy enough (not going to drop it to test) and my screen behaves the same as without the screen as far as interaction goes, it doesn't interfere with my finger movements. Probably wouldn't buy again though.

It's a nice screen protector but it does not fit edge to edge. I mean, it's cheap and it'll likely do the job with any decent case you get (I'm currently using a Tech 21 case), but I would rather it at least covered the edges a little better. There's a slight gap and you notice it while watching videos. Also, unless you've put plenty of screen protectors on yourself, I wouldn't advise this case as it is not the easiest to install.

The protector appears to be durable and went on easily, but it doesn't fully cover the entirety of the Pixel 3, and when using the Pixel 3's Otterbox case, it causes air bubbles due to where the case puts pressure. It'll work for now but I'll likely replace with a different protector relatively soon.Also, it didn't come with a squeegee, which isn't a big deal, but makes getting most of the air bubbles out a bit more difficult.

Overall the product is as advertised and installation and packaging were easy and great. Like that the price for 3 is very generous - the only reason for 2 stars is that the measurements of the glass seems off in total as the glass though adheres perfectly seem to overhang the border of the Pixel 3 screen - the top and bottom to the point that it gathers dust under it. The horizontal length seems to be just a little shy in covering the entire screen.Considering I bought it for screen protection prior to launch date I am not complaining just pointing out what looks like needs adjustment, will be returning these for refund.

This screen protector doesn't stick to the very top and bottom ends of the phone screen; it seems like it's a little too long. Tried both screen protectors that came in the box and neither would stick to the curved ends of the phone. Will be using this screen protector until I'm able to find a better one.It's worth noting to anyone reading these reviews that this phone suffers from the same issue as the other 2 pixels and most screen protectors (including this one) will leave a small gap on the left and right sides of the screen; and that might be extremely annoying to some people.

I guess since the reviews on this product page range from a phone case to ginger candy I have to preface that I'm referring to a glass screen protector for a Google Pixel 3.The glass seems to be decent quality, installed easily, with no bubbles. The problem is that it does not fit well. I have the speakers and camera holes lined up on the top and bottom, but there is a slight tilt to the alignment. The worst part is the extra space on either side. It does not cover the whole width on the screen. When applied it looks like it was made for the wrong phone.

seems like a quality product, but it doesn't fit well unfortunately. i will try to upload pictures soon. fit is a little narrow so it cuts into the edges of the display, as well as being a little too long, so you get (or at least i do) an overhang on the top and bottom that doesn't quite touch the screen.

The edges don't stick and it's not wide enough. I usually put my phone on a soft surface face down and put something heavy on top of it like a milk jug filled with water for 10 minutes to get a good seal. But not even this was enough to make the edges stick. It's also not wide enough. I managed to get it in the center and the edge of the screen protector did not reach the edges of the display. This made the display ugly because it skewed the display image on the sides.