GT Omega Classic Wheel Stand - GT Omega Steering Wheel Stand for Logitech Steering Wheel G923, Logitech G29, Logitech G920 with V1 and V2 Shifter Mounts - Thrustmaster T300, T500 TX, TH8A

I will say that this is one amazing piece of equipment! Very well designed. At first, I though the lack of adjustability of the pedal rest was going to be an issue, but you wouldn't adjust the floor in your race car, so... Well, you could, but at least in your car, you don't! It's not typical, and it's not necessary. However, if you are really that picky about floor angle, it's really easy to build a custom piece to change the angle.It came with all the necessary screws for mounting my Thrustmaster TX Ferrari 458 bundle. It's height adjustable, and there are two angles of adjustment for the braces, which can also be angled completely flat for stowing away. The wheel/motor plate at the top of the unit is adjustable as well, allowing tilt adjustment of about 15 degrees, give or take. The feet on the bottom of the unit screw into the frame, and because they are screws, it provides pretty much unlimited micro adjustment for those uneven floors. Speaking of floors, it won't really slide either, because the feet are padded with rubber; however, if you drive like a maniac like me and you pull wheel toward you, it will kind of tip down into your lap. With the seat fitted on (see comment below), that can't happen at all. However, generally, most drivers won't have a problem with pulling the wheel. In fact, if you pull the wheel towards you, that is more the driver's fault than the wheel stand (sorry).There is a little side-to-side flex, as well as very tiny up and down flex, but overall it is plenty stable. Not really sure what I can do to alleviate the flex...add some extra bracing, perhaps.The fact that this stand is upgradeable with a seat frame and racing attachment makes this stand a super value. Plus, the shifter arm and plates for both Thrustmaster/Logitech and Fanatec shifters, which can be mounted on either side of the stand, were included as well!

This is a very basic wheel stand. Good for your kids or begginer simulation as things can just be mounted to it, then folded up to be stored away.Good things-1-Supports pedals, wheel and shifter.2-Frame allows you to pull a chair up to it or connect one via the metal rails on bottom (adjustable racing seats).3-Folds up for storage.4-Durable all metal construction and bolts.The bad-1- Even while folded, can be quite bulky especially if you have the steering wheel and shifter knob attached. Would require alot more work to fold if a sliding seat was installed.2-No way to hide the unsightly wires dangling EVERYWHERE.3-The pedal mount kinda sucks, needs modifications to keep it in place or it just fall off when folded up. You may have to drill new holes on the bottom to bold it on.4-Its kinda ugly looking, even having it folded up in the corner of your room with everything attached. 5- if your looking for something more realistic you can mount screens and a dashboard, etc to, you may want to look elsewhere.

I like how fast and easy this was to set up out of the box.It is easy to fold up and move as needed. Compact to store. Easy to take out of storage and set back up.Perfect for my needs!The one thing I am OK with, but would prefer a different solution for, is the mounting of my Thrustmaster T3PA pedals.The mounting plate holes did not properly align for me, and I was only able to get one screw in. This is secure enough. But a better solution might be for the GTOmega Racing Stand to come with (2) two "Z" brackets. It comes with one, which holds the base of the pedals at the end nearest the driver. A second "Z" bracket could be mounted at the end of the base furthest from the driver. This would give a wide range of positional variability, with tolerances set by the GTOmega build team. I want to order a "Z" bracket and the underlying strap to implement this solution, but there is no part number on the assembly sheet, or invoice, to identify it by, and no contact information for buying replacement parts. This is a minor complaint.I am very happy with my GTOmega Racing Stand.

What's good about this stand? I love that it wobbles back and forth and is not stable. I love how no instructions were included. I LOVE how half of the screws don't even fit into this stand.Just amazing. (It's incredibly terrible, STAY AWAY)

Unit construction is good, though this isn't pre-drilled for Fanatec V3 Inverted pedals. Very disappointing.

This stand is solid and arrived mostly assembled. With the included tools I had all my hardware mounted and the stand adjusted in less than an hour. Everything you need is included and the two shifter mounts that were included are a nice bonus since they were previously sold separately. The only complaint I have is that there were absolutely no printed instructions in the box, I was able to manage without them, but it would be nice if they were included. As for movement there is a little bit, but you can expect that from any stand and judging by the designs I've seen this would likely be the most sturdy stand you can get without using a full rig. I would definitely recommend this to anyone needing to mount a wheel however if you intend to use this from the couch you'll likely not be able to use the shifter mounts as they prevent you from getting the stand close enough.

I can however say this is a well made product. I had to return because the steering wheel didnt work work out. other than that a solid well made product. the return process however is a living nightmare hence the 2 stars. almost 3 weeks and still no refund.

Very sturdy. Doesnt wobble or shake. My only beef is the foot pedals arent secured. After a few laps of switching between pedals the whole pedal unit slides out the groove and you have to pause to readjust the pedals.

Prodotto arrivato in anticipo, ottimo !Tutto perfetto, stabilissimo, materiali di costruzione al top, veramente un prodotto di alta qualità

Love this stand. It came completely as advertised. It's collapsed in the box, assembly is super simple. Came with wing nuts for hard mounting pedals and wheel to that stand. I have a Logitech G29 and the bolt pattern fitment was perfect. Stand is very sturdy and had 4 rubber covered feet for the base. So the stand grips either carpet or a smooth floor surface very well. Like hardwood, laminate or tile floor, without sliding around. The twin spar design is awesome. Your legs fit through the centre perfectly. So two footing brake and gas is very easy or heel toeing with your cluth. I would suggest this stand to anyone in the market. If your not wanting to spend the money on a play seat, the GT Omega stand is wicked option.

Solide, idéal pour faire du simracing dans son canapé. Je l'ai acheté pour y installer un Thrustmaster TX Racing Wheel Leather Edition avec pédalier T3PA + le levier de vitesse TH8A, l'ensemble tient parfaitement et s’adapte à ma morphologie grâce aux différents réglages, ce qui fait qu'on est très bien installé. Du coup, l'achat d'un playseat n'est pas indispensable. En plus, pas de barre qui gène entre les jambes. Enfin, il peut se replier avec le matos installé et tient debout tout seul.Le tout petit moins: l'ensemble pèse lourd (environ 15kg) mais c'est gage de solidité et de stabilité pendant les courses!! :-)Je vous le conseille vivement!!!

Ich nutze diesen Wheelstand zusammen mit einem Thrustmaster TMX und den Thrustmaster T3PA Pedalen.Der Aufbau war völlig unkompliziert da der Wheelstand komplett vormontiert geliefert wird. Die Pedale konnte ich mit einer der mitgelieferten Flügelschrauben befestigen. Lediglich eine Unterlegscheibe habe ich aus meinem eigenen Fundus benutzt.Der Stand ist stabil und rutscht nicht (ich nutze ihn auf Fliesen). Schön ist ebenfalls das man die Standfüße durch rein- bzw rausdrehen individuell in der Höhe einstellen und damit evtl. vorkommende Unebenheiten der Fliesen ausgleichen kann.Das Auf- und Abbauen das WheelStands geht ebenfalls recht einfach von der Hand, da man dafür nur zwei Sterngriffschrauben lösen muss. Das Lenkrad und die Pedale können voll montiert bleiben.Schade ist nur, das die beiden Sterngriffschrauben im zusammengeklappten Zustand nicht wieder an die selbe Stelle eingeschraubt werden können. Ich nutze dafür (um Sterngriffschrauben nicht zu verlegen) die die Schraub-Öffnungen die für die Erweiterung zu einen kompletten Rig gedacht sind.

El soporte, es muy estable y cómodo. Con posibilidad de ampliación.Es pesado, lo que le da seguridad. Y además se pliega, para quien no tenga mucho espacio.