GP-EXTREME–Thermal pad 80x40x1.5mm | Excellent heat conduction | Ideal Gap Filler | Easy installation | Thermal Conductivity 12W/mK.

These thermal pads are better than the stock blue we all see usually dissapating heat at 6mk that goes for ARTIC pads also THERMAL GRIZZLY PADS are 8mk and are far superior to the stock and ARTIC and the GLID are 12mk they transfer heat like the sun and keep the temps down better than grizzly as I have tried them ALL an can recommend GLID. If you want to look after your desktop /laptop vram chips an like it's a must especially for laptops as when I got mine I had to repaste with thermal grizzly paste at 12.5 mk the best an done the gpu also and cut to size the new pads. Gpu idle was 44c with blue artic with glid idle at 37c max on artic 75c glid 58c. Dont hesitate to BUY NOW get the best bees knees

Gelid Solutions GP-Ultimate is pricy but it work well to transfer heat and cool my Samsung M.2 SSDs RAID enclosure. I found about a 4C drop in temperature over regular silicone heat pads; almost the same temperature drop as turning on the enclosure fan! The enclosure temperature mostly sits in the low 30Cs now. Gelid pads seem to be mineral loaded and are formable with care but are much less compressible than silicone pads. Hence, you'll need to precisely adjust the pad thickness prior to final installation If your enclosure makes thermal contact with the SSD on closing. That said, the Gelid pads transfer heat better once installed. Hence five stars.

Bought two packs of these pads to replace the stock material on my Xbox One X as I was replacing the paste on the APU and thought I may as well do the lot. The 2.0mm was what I figured out you needed for the XBox, and from other reviews I gathered I’d need two packs as this is only 8x4cm. Turns out, if you’re not worried about the Southbridge chip on the reverse of the board, you can easily do the 12 RAM chips (about 11x14mm each) and the VRMs with a single sheet of this. As I bought two anyway I used the second pack to do the Southbridge but could have fudged it with the remaining scraps or reused the original pad if I needed to. All the credit can’t just go to this material as I obviously replaced the paste as well, but the XBox fan has dropped about 25dB and is noticeably quieter. Essentially silent in a normal room on high load from demanding games. I totally believe the higher-than-average specs on this material and it was easy to use and a joy to apply (especially compared to the mess Made taking the stock pads off). Aside from the rather hefty price tag I’d say this stuff is perfect, and probably overkill for my application, but well recommended!

I used these thermal pads to replace the stock thermal pads on my Asus RTX 2070 MINI - these thermal pads work well and they definitely have reduced VRM and VRAM temperature, however they are expensive and you only get 80x40 in size. I would really like to see a reduction in price or a bigger size you get for the money, 100x100 at a minimum would be nice. I would only recommend buying these (at the current price of £13.90) if you are an enthusiast who is looking for every ounce of performance and reduced temperature. If you are just looking for replacement pads, you may be better served by other and cheaper options.

Bought for PS4, works great.

After a fair amount of research I came to the conclusion that Gelid is one of the the best, or at least better thermal pad solutions on the market... I wouldn't say it's cheap, but it is fairly priced; it stung a little bit that I needed to get 1 mm, 2 mm and 3 mm pieces to be sure that I would have all the right thicknesses to repad my graphics card, and that of course starts to add up. However that isn't Gelid's fault... Thermally I can't actually definitive answer as to how much it dropped temperatures, because I was actually installing an aftermarket dual water block on my GPU so it wouldn't be a like-for-like comparison... The water blocks did come with thermal pants, however like I say, having already spent a fortune, I wanted to install the best... What I can say is that with the hefty AIB three slot triple fan blower on the card with stock pads and compund, I was getting about 80C degrees on the GPU die, and nearly 90C on the GPU memory... On the dual front and rear EK water blocks with these Gelid thermal pads on the memory, and thermal grizzly kryonaut on the die, both die and memory peak at 62C now. With much lower (and therefore quieter) fan speeds. 👍😁👍

Top quality

Package was intact but product inside had sides a bit squeezed together probably it was packed together with another delivery. At least affected part wasn't a lot it was still usable.