Extreme Max 5001.5013 Lever Lift Stand

This was helpful to lift my sled. I am not able to lift my snowmobile by myself. However, after only a few times used ...the hook on the end used for leverage has bent. With a bent hook it is now difficult for to stay positioned on the snowmobile. Otherwise I would rate it 5 stars because as a female rider, It’s helpful for lifting my snowmobile.**** Update, I received a replacement hook at no charge. I’m back working fine. Changed review to 5 stars. Works well to help lift my snowmobile.

This lift arrived well-packaged to protect it from shipping damage. It came with good directions and assembled in minutes. The lift makes lifting the rear or front of my sled effortless with the single, relatively easy pull of the lever. You can put a pin (included) in the mechanism which prevents the sled from slamming back down when you're under it.The lift hoists my 2020 MXZ X-RS up high enough to get the track off the ground for any number of maintenance or other projects. It can lift the front of the sled off the ground which helps with switching carbides or other related projects. I like this lift a lot and a few of my buddies will probably buy one as well.

I wish I had this when I purchased the snowmobile I now am stuck with. It doesn't run right after warming up so yeah, I got screwed on it..... my fault for not checking it out better... LOL!. I would have walked away if I had been able to really test run it on a stand like this. I have run it pretty fast on this stand and it doesn't even flinch. I feel it is a very safe way to really test out the running gear on your sled and a great way to store it off of the ground. It also takes little effort to raise the sled up on it.

Went together easily. Welds aren’t beautiful but they are strong. Easily lifted my 2020 Ski Doo G4 Renegade off the floor. Good unit for the price. I might buy another one to keep in the trailer.

They did not provide the correct amount of plastic washers per the instructions( which even says are needed to aid in the pivot motion so it is not metal on metal. )Design is good. Fabricating is decent. Welding is sub par at best. Their is porosity or pitting in many of the welds. Between that and the small amount of weld deposited I was a bit disappointed as it is not as much cosmetic as it is a structural integrity issue. Still it was fabricated together well and coated well. The welds don’t really support to much weight the just hold it together so I assume it will be more than strong enough. My sled weighs 700lbs so we will see if it lasts.

I've used a lot of things to hold the snowmobile's track off the ground. Anything from a block of wood to a tie down strap from tree branch. This tool is easy to assemble and a 10-year old could life the track off the ground with it. The leverage is amazing. One hand operation without an issue. My rear lift bar is really high and I am at the last adjustment on it. That might be the only downside. If your tunnel is REALLY tall at the end it may not work. I didn't measure the distance. On its last adjustment it still lifts the entire track 3-4 inches off the ground at its lowest point.

One bolt was too short, fortunately I had a Grade 3 bolt kicking around that fit perfectly.Other than that, this jack works well. It is not extremely heavy-duty, so I must make sure the base is as close to the sled so it doesn’t bend toward the sled when the sled is lifted.Other than that, I am totally happy with it.Between this and three red dollies, I can easily rotate the sled 180 degrees so it’s always ready to drive right out my narrow basement door.I also always keep the track off the ground and do some work on my sled, this works perfect for both.I tried the large sled mover with large pneumatic tires. Trying to lift a Grand Touring 2-up sled put so much strain on that contraption that I was afraid to be near it when the sled was lifted the mover was literally bending!

Had these on my Yamahas for 2 years now, they’ve worked as designed that long but the one I use on my Apex hasn’t held up - the hook bent to the point where the sled slides off now. I had to try to bend it back, so who knows how long it will last before it falls again. Kinda disappointed...what would it take to make a sturdier hook to hold the grab bar? Just one or two steel gauges higher and it wouldn’t bend. Might be better for a lighter 2 stroke but doesn’t work much more than 2 years on a heavier sled.

Je lève mon Renagade sans forcer et lèverai mon nouvel Expédition sans problèmes . Très simple à assembler et doté d’un mécanisme sans effort ou presque afin de lever la motoneige, incomparable avec ce que j’avais avant et très stable .Je recommande fortement

Very well built. I have a Rev XM summit 146”. Third highest setting is enough to take the weight off the suspension in the garage. Second highest setting lifts the track a couple inches off the ground. Highest setting a couple inches higher.

A safe tool to use for my mother's snowmobile. She was able to set it up herself and put it in place. It lasted through harsh weather. She also has a bad arm, which she was still able to use lift appropriately and safely. If she can do it, so can you. She has recommended it to some friends of hers.

This worked great to hold up my snowmobile. It was a bit difficult to get it on/off the hook, but once on it, it worked well. It wasn't the most sturdiest but it didn't fall over or anything. Was happy with it.

Très bonne qualité, Je l'utilise avec ma motoneige Yamaha Venture, lève très haut, c'est parfait et le prix est excellent.