Original Ender 3 Pro Bed Clips Clamp 7mm for Creality Ender 3 V2 Ender 3S Ender 5 Pro Ender 7 CR-20 PRO CR-10S Pro 3D Printer Heated Bed Glass Bed Platform (Bed Clips)

In order to get these to fit with your glass bed, you'll have to remove the magnetic surface. The magnetic part is being held on with adhesive, so it's a bit of a pain to get off, but these clips are far better than binder clips.You'll also want to add nylock nuts to the underside of your print bed to keep them from just spinning in place. It turns out that my magnetic surface was actually adhered to the screw heads, so by removing that, my screws were just free floating.Since you're messing with the bed leveling, you might want to do all four of the following at once: stronger springs, nylock nuts, glass bed, these clips.

Bought these for an Ender 5 Pro with the glass bed upgrade. I did not remove the magnetic sticker below the original print bed. Had to strech these out to fit, scratched the glass. You will need to remove that magnetic layer first! This is probably mentioned in other reviews that I did not see. No instructions or anything so don't throw caution to the wind like me!

Works on my Ender 3 pro with the Creality glass bed, but you have to remove the magnetic pad stuck to the heat bed. I have used both the magnetic bed and the Creality glass bed and I like the glass bed better so I had no qualms about removing the magnetic material from the heat bed. They clips are a lower profile then the binder clips and looks a lot nicer.

Cr-10V3 come with 8bit mainboard. Open the manual for the CR Touch and it says 32bit mainboard only. I decided to try it out on my Ender 3 pro. If you’re experienced with compiling firmware, it’ll be a pretty simple install. My guess is most people are not. It took a few days of adjusting to get perfect first layer. I’m also using a glass bed and it’s very flat. The probe rattles in the case and it’s pretty obnoxious. After using it for a few days I noticed the light blinking red half way through longer prints. I’m guessing it could have something to do with the probe rattling around? To be honest, I’m not even 100% sure it’s working well or if my bed is just perfectly level lol! I haven’t seen the slightest adjustment on the z axis ever while printing. I’ll give it another week before I decide if it’s helpful enough to keep it. But I’m leaning towards not.

My printer on my came with 2 clips. I switched to binder clips but I kept bumping into them. I wanted to go back to the stock clips and these fit perfectly on the print bed.

Pros: Heavy Duty Red Wheels; Silicon Spacers; Holding great using only M420 S1 for abl.Cons: Was a bit of a pain to level, but doable.These work great so far. Been on a printer that I just built. Took a while to get the bed level, even with using bed leveling visualizer from octoprint; But now it is set and forget.I probes the bed a few times manually after each print for a few prints and it remained the same. Been printing 8+ hours a day for a weekwith M420 S1 gcode in place of G29 (load mesh vs creating a mesh every run) with 0 problems.Love it.

Purchased for my Longer LK5 Pro, they fit wonderfully. When my boss first saw the printer in action he remarked about the binder clips. "You paid how much for a printer and that's how it's held together?" I had to agree with him. These stainless clips fit snugly and hold the glass to the aluminum heat bed. They are also super low profile (install with holes up), nearly eliminating the chance of your nozzle crashing into a poorly placed binder clip.

I bought these clips not sure if it would work for me as the standard clip upgrades I purchased kept flying off of the bed. These specifically state that they are for 4mm beds, but my bed is only 3mm. When I got them in and put them on, they worked perfectly! If you're hesitant to get good clips for your glass bed on an ender 3 - GET THESE!!

These clips fit the Ender 3 Pro with a Glass Bed, but only if the magnetic surface is removed from the build plate i.e. glass bed directly onto the aluminium plate.If you have left the adhesive-attached magnetic surface on the bed, and put the glass bed on top of this then you can't fit these clips on as the overall thickness is too great - you'll have to stick with the bulldog clips.

I’m using these on my Tronxy x5sa pro. I’ve had to squeeze them with a big pair of pliers because they were a little too big but now they work perfectly (and I’m not going n to ruin any more nozzles!) The little tabs are great for getting them off the bed too. Ps. I use them with the flat to the top, much lower profile.

Not really much to say about these, except they appear identical to the stock clips on my Voxelab Aquila.I bought these as the 2 clips supplied didn't hold the bed securely enough. With 4, it's rock solid.

Am use it on my enter 3 not pro. It’s went great and it’s good for ended 3/pro

Worked as intended, nice snug fit so hold the glass to the bed well.Need to get a little screwdriver or handy dandy scraper to get them off, but rarely need to removed them.