All-Fit Automotive Lip Kit – Universal Fit for Style & Protection – Durable, Flexible Material for Bumpers and/or Side Skirts – Easy-to-Install Automotive Exterior Accessories (1.5” W x 9’ L, Black)

The All-Fit front bumper lip is definitely better quality compared to other ones I have seen. I actually returned another one to order this after seeing how thin and weak it feels.The installation process was easy, but I just took my time and i really measured out everything before I finally applied the adhesive and stick the lip on. The adhesive seemed pretty strong after installing the lip, however, I did notice some parts didn't stick as good, so, I decided to apply the screws at every 12-15 inches to reinforce the installation.It looks great now, but I am hoping I can find a matching wrap red color for the chrome part of my car. This red is more on the light side.Update:The front bumper lip is holding up every well after installation; it has been 2 months or more now. There was several incidents with deep dip in the roads of LA, California. But no visible scratches on the viewable parts of the lip. The screws definitely help hold it in place during those dip scraping.I wasn't able to get exact matching wrap colors but I got close enough and it actually turned out okay at slightly different shades.I also ordered the side lip after seeing the results of the bumper. I don't regret it at all. The staffs at All-Fit was very helpful and convinced me to give it a try before I chickens out and wanted to returning it.I thank them for convincing me. They also looked into whether my different Mazda design could accommodate the lip. It turns out you can apply the screws onto the side plastic part of the car, for Mazda owners out there. Just don't screw into the connection tabs every 2-3 feet and it will be fine.I'm happy with the lips. I don't think I will do a back lip however. I don't want the car to be too attention grabbing. From the back view, it looks like a regular Mazda. =)

Nice to be able buy an American made product. Kit came with plenty of hard ware to attach to car to supplement the 3M tape. Also came with cleaner and activator for the glue tape. This is a very complete kit plus some bling thrown in too. I ordered the 3.5 inch kit since my car rides high.Since it it's rather large it has a bit of weight to it but is sturdy and the tape and fasteners will hold it well. I stated from the middle of car and worked way out. I also took a marker and marked the center of the product for a starting point and being sure I'd have enough to do each side. I wasn't sure about how it would look but liking the look now. I occasionally take this car to the drag strip and I actually picked up 2mph at the traps in the 1/8 mile. So not only does it look cool it actually does have some performance benefit. Have not taken a lot highway trip so don't know if or how it may affect gas mileage.

Good quality product just overpriced for flexible plastic with an adhesive lip. Had to buy 2 pkgs of the 3.5" for my rv but looks good and should last. Good instructions (video) and all parts supplied for installation. I chose not to use the adhesive on my fiberglass body but supplied self tapping screws with square plastic washers every 6-8" and closer at corners hold it in place very well. (every little bit of aerodynamics helps these 10 mpg gas hog beasts) Hoping this and Thorton Performance chip (only $59-89 I got the Stage 3) will give me more power and 2-5 mpg extra. Immediate performance improvement when chip was plugged in. Removes instantly with no changes to factory specs.

There are a few of these products on the market, all claiming to do the same thing. I decided with all fit )Mid lip) based on the reviews. I plan on lowering the car by roughly 1.5 inches, so the mid lip will give it a near slammed look without it being slammed. (Picture is before lowering)Installation was a little trickier than expected, but there was enough extra material to start over again if needed. I have a 1993 Mustang and the first corner had to be redone a couple times, but after that, the installation went smoothly. I recommend pre-fitting and determining where the stress cuts need to be made before pulling off the adhesive backing. There is just enough hardware to secure it in place so you don’t want to lose any. Four out of five stars because the tape would not stick long enough to let me use the screws. I used clamps. The directions say that it is possible to just use the tape but I disagree. After installation the car looks great and I am very happy. I also decided to cut each end of the chin spoiler to match the angle of the inner fender. Otherwise the corner sticks out pretty far and in my opinion doesn’t look as good.

After All the prep workInstallation was pretty straight forward and easyReally liked the outcome although after driving it for a while noticed the adhesive didn’t stick in some of the curves from the bumper. Ended up using the screws to fasten it.Taken it to multiple car washes and has held up well since then

The all-fit mid-lip looks very much OEM, and gives the impression as if it came straight from the car manufacturer. Perfectly follows the bodykit lines of the SUV giving it a much lowered, and more elegant stance. Thanks AJ for the assistance in helping choose the correct size/width. Super cool guy, very responsive and will go the extra mile to answer your inquiries

Protip: Don't Buy This. Quality is mediocre-good (probably better than most/all other brands out there though). Color is definitely more pink than red by any measure (But still wouldn't match either color). I'm sure the black color would look fine. However "red" is a TERRIBLE choice. Glue held great for a few days of driving, even at high-speeds, ( I didn't use the screws to add extra security-partially because I wasn't sure about keeping it on my Camaro and Partially because MANY of the screws were MISSING from the package) before I decided to swallow my pride and remove them. If you are on the fence between any color vs Black, either roll the dice and go with black or move along.

Product is good for the price and sturdy and easy to use recommend

Looks awesome, I was searching for a lip for this chassis of accord and my buddy recommended this it’s perfect

Installation is a bit tougher due to stronger rubber vs the light foam the ezlips use. Had to use additional hardware since the glue didn't stick so well around bends.