Akasa Newton CTN, Designed for Intel® 11th Generation NUC Core™ i3 (Tiger Canyon), Compact 1.06L Aluminium Fanless Case, Supports one M.2 SSD and VESA mounting, A-NUC75-M1B

I have the NUC85iBEH model. It has been a faithful performer, but it could heat a small house under heavy load, and the fan noise was starting to bother me. The design of the NUC made it impossible to get to the fan without removing the entire motherboard, so I saw the Akasa Plato X8 as an opportunity to permenantly resolve my heat and fan issues by eliminating the fan altogether. You remove the motherboard from the original case, and place it in the Plato X8.First of all, the pictures of the Akasa should tell you that your resulting case is going to take up significantly more space in your rack or cabinet. You are replacing the small NUC case with a hunk of aluminum that is a giant heat sink which will absorb and spread the heat from your CPU to obviate the need for a fan and the noise that comes with it.In my eyes, this hefty aluminum hunk of heat sink is beautiful, and it abolutely works. All of the front and rear jacks on your original NUC case are duplicated. In fact, the rear panel has two extra openings for Wifi antennas, which are not included with the case. And the wifi antennas which would work with this case are the kind that use two of the vertical black sticks which have wires that plug into the Wifi card on your computer. The original NUC case uses wires that run along the inside of the box. That arrangement does not work with the replacement solid aluminium Plato X8. The aluminum case would block the wifi signal from a wire antenna inside the enclosure. The antenna kits are readily available on Amazon. For my NUC85iBEH, the wifi card required an antenna array with MHF4 connections. Connecting and disconnecting the tiny antenna leads was the most challenging part of the assembly.For all the rest of the connections, the Plato X8 kit supplied the cables to connect to the motherboard. The instructions are not verbose and use diagrams to describe the various parts and how to install them. When you get the motherboard out of the original case, You have to remove the thermal compound underneath the CPU and wipe the exposed area with alcohol gently to fully clean it. You use the supplied thermal compound to fully coat the bottom of the CPU which touches an aluminum block underneath it in the new case. Once you have screwed the motherboard down, connect the cables, and you are ready to power up. I was slow and cautious, and it took me about an hour to remove the motherboard from the original case, clean the CPU contact points, screw the motherboard down, and connect all the cables.With my NUC85iBEH, I lost none of the controls or connections on the front and back panels of the original case. My original case did have a micro SD card slot on the side of the case, so that is lost with the new case, but it is the only feature lost for me. That did not bother me, as I had never used it.When I pressed the front button to boot up, the comptuter booted up in total silence. There is no fan noise, ever. I have had the computer on for two solid days, and the top of the alumimum case is a little warm - nothing more. Using the CAM software to monitor CPU temperature after running for two days, I show a temperature of 37 degrees Celcius. Of course, this computer is used as an HTPC to listen to music and watch videos, so it is really never fully taxed in my usage. Nonethess, the fan used to come on all the time, and was distracting in a small room. And if I ever waited too long to clean the fan, the computer could get hot enough to occasionally have a thermal shutdown. Now there is no more fan to clean, and the motherboard assembly is in a fully enclosed case which should make it invulnerable to dust.I have attached a picture of the finished case in operation as well as my old NUC case and fan in its disassembled state. I did not take a picture of the motherboard installed in either case, but now that the project is finished, I did not want to open the new case back up.The Akasa Plato X8 is beautiful and practical, and I love it.

I bought the original Intel NUC8i7BEH because it has a powerful CPU in a small package. The GPU of the i7 8559U is Iris Pro 655, which is also currently the most powerful Intel GPU. It's an ideal computer for playing UHD bluray discs using PowerDVD. It's also equipped with a Thunderbolt 3 port for external GPU expansion. I was able to develop VR programs and play VR games using the NUC plus an nVidia external GPU. However, the fan sound has been clicking from the purchase. More recently, after an extended period of VR programs, the fan started to make more violent noises. I was initially thinking of having Intel fix the issue until I found the Akasa Turing case. In fact, another importance use of the NUC for me is for music. I connect it to a Sony TA-ZH1ES headphone amplifier for SACD playback or a Sony MDR-HW700DS for multichannel music. When I use the analog amplifier, I also use a pair of Audeze LCD-MX4s. The fact that these are open headphones make the computer fan noise very obvious. Therefore, I decided to go fanless by purchasing the Turing case.The installation was relatively trouble free. I hope Akasa could have included instructions on how to take the NUC motherboard out. To figure it out myself, I found that it's important to remove those static foams first, which were tape-glued to the inside walls of the NUC case. Then, take only those two black screws, turn over the NUC, and pull the motherboard out. Also notice that, you need to keep the microphone array assembly. This is illustrated on the instructions. After taking the NUC apart, I found the original heatsink and fans were too tiny to be thermal effective, even smaller than a typical laptop heatsink and fan. No wonder that the NUC often reached 100C not even underload. Additionally, the original NUC case had a thick thermal pad for the M.2 SSD module while the Turing case just leaves the SSD breathing on its own. I purchased an M.2 heatsink to be installed on the SSD.If you want to keep Wifi and Bluetooth, separate antennas need to be purchased. Be very careful about the antenna connector size. The Intel Nuc uses Intel 9560 wireless card. Antennas need to be made to support this model. I found the most common antennas on Amazon usually have a larger and incompatible connector size. Additionally, in order to get reliable Wifi and Bluetooth signal within room range, a pair of decent antennas are needed. I actually bought two pairs, one of rod-like shape, and another flat. I found the rod-shaped antennas had much better range. This is especially true for the Bluetooth signals.The finished build is 3-4 times the size of the original NUC case. The Turing case can stand upright. Therefore the occupied area on a desk is actually smaller. The reduction on CPU temperature and fan noise is incredible. So far, it normally runs at about 40C when all cores are at 4.5GHz. Under the heaviest load I could give, it never goes over 80C. Of course there in no fan sound at all. But I start hearing coil whine from the NUC board. Well, that probably means quiet for a computer.The case has many sharp edges and corners. And it's heavy. Considering its benefits, the design drawbacks are negligible. I think Intel indeed cut corners on its NUC in order to deliver a tiny package. To get the full potential of the i7 8559U, the Akasa Turing is a well-balanced choice.

Transferred my Media PC NUC8i5BEK (short case, no 2.5" SSD) into this case and am loving it so far.Pros:No fan = no noise + less dustGood cooling capacity (seeing idle in the 30C range and full sustained load in the 60C range so far with a mildly undervolted CPU)The case looks great and feels well-made.Assembling the NUC board into the case is relatively easy if you've ever touched the inside of a PC before.Cons:WiFi cables+antennas are not included.Thermal compound cleaning solution for removing the NUC's original thermal compound is not included.Provided instructions did not include steps for disassembly of the original NUC hardwareCase fins are a little sharp at the edgesWiFi antenna positioning can be a little awkward depending on case orientation.

Easy AssemblyGood thermals (40-65F most of the time)Antenna holes (overall precise fit)Feels sturdy and solid (no squeaky parts)Nice Monolith-like modern styleRunning i7-8559U NUC on win 10 pro, NVMe + 2.5" SSD + dual RAM, the case spreads heat evenly and quickly. The whole case gets warm but not uncomfortably hot. It does not dissipate heat as quickly as active heat sink as expected but it does not stay above 65F for more than 10 seconds under load. I do see max core temp as high as 70-80F sporadically but not sustained.This case feels like using RPi 4 on Flirc case (the whole case is an aluminum heat sink).Assembly is a breeze, snug fit panels, solid aluminum construction with nice modern style.Get IPEX MHF4 antenna cable for WiFi card.

Like most people leaving ratings, I found the fan to the NUC (NUC8i3) to be terribly loud to the point of turning the NUC off when not in use instead of letting it idle.Finding Akasa's fanless option seemed like the best (albeit expensive) option. However, once getting the case delivered you can see the price is well worth it.Not only do you get the case but also:* Thermal compound* SATA SSD cables (for additional SATA SSD)* SATA SSD mounting kit* VESA backets* M.2 SSD cooling components (thermal pads and aluminum block)Assembly was easy once checking out the video.The NUC is now silent and hovering around 30c, this is probably due to me not adding enough compound, but will rectify this shortly.Additional, the SATA power cable was smashed during delivery, after alerting Akasa about it, their team did a really good job in getting me a new cable as they followed up on almost a daily basis until the cable was in my hands.The only downsides I encountered are* The IR redirector (plastic rod) isn't lining up with the receiver on the NUC, haven't tested yet* The power LED is incredibly bright (had to add a bit of tape to mute the shine)5/5 would definitely buy again

Initially was a bit sceptical and annoyed that this was way overpriced for just a cooling case, paying another premium after spending £500 for an Intel NUC (NUC12WSHi5). But after suffering from high temperatures for nearly a year, constantly hitting 97-100 Degrees, I felt lost and thought I made a mistake in buying an Intel NUC. Tried out various DIY projects to keep this thing cool, but none really helped until I gave this case a chance. Installation didn't take long and all ports are well aligned. I would highly advise mounting the side edges/panels as the corners without it are very sharp and you don't want to drop that case on your foot.Booted up Proxmox and all the VMs, and to my surprise, when I checked the temperature sensors, it was around 32-41 Degrees. I ran some additional tests with transcoding and other CPU-intensive tasks and the temperature was around 65 Degrees max. The case was warm to the touch, but I hooked up a dual 120mm USB Fan (lowest speed mode) on top of the case and the temp went further down to 51 Degrees. NVMe was around 41-43 Degrees. I let it run for a week and constantly checked the temperatures and it was stable within those degrees and never went above 61 Degrees when doing multiple Plex streams and Tdarr transcoding. Absolutely amazed with the results and never expected temperatures that low under load. To add, I used Arctic MX-6 Thermal Paste and maximum performance set in the BIOS. I know the price of this case will turn many off, but in my opinion, this case is worth every penny and I would highly recommend this for anyone using an Intel NUC as a small server running various VMs including 50+ Docker Containers. Well Done Akasa!

What a case! Cooling performance is much better, than Akasa Turing FX. NUC12 with I7-1260P is about 50 degrees C, when decode video with Handbrake. Good job Akasa!

Il manque toutes pièces détachée. C'est à dire les supports SSD, toutes les vis, la pâte thermique. Ce boîtier est inutisable en l'état. Je l'ai commandé 2 fois et dans les deux cas il manquait toutes les pièces détachées.

Very nice case.Finally no fan noise, which is pretty loud now and then on the NUC.Core temperature averages between 47 and 65 degrees celcius.Installing the board was pretty easy.