Cooper & Hunter 9,000 BTU 230V Single Zone Wall Mount Ductless Mini Split Air Conditioner & Heat Pump – 21.3 SEER2 – 16FT Installation Kit – Refrigerant Pre-Charged – Inverter

This was a good purchase--so far. I was hesitant because of mixed reviews but the unit arrived on time, was well packaged, installation went well and it works fine. The instructions are clear and came with an accessory kit that is pretty chintzy but mostly does the job (i would be annoyed if i had paid extra for it). The unit works well so far in the spring but hasn't been tested in summer or winter. I purchased an outside wall mount separately on Amazon but the outside unit's feet are an open-side-down U channel and do not fit the width of the wall mount arms or the isolation pads that came with either the mount (circular and too big) or the minisplit (rectangular and probably for floor mounting) - so I had to add additional parts. Not sure if these dimensions are available but something to be prepared for. Also, the lineset pipe-wrap doesn't stick to itself or anything else so be prepared to deal with that. The electrical/control cable ends have connectors on the ends which fit the outside unit, but not the inside unit so they have to be removed. The condensate drain line is pretty flimsy. Little annoying things, but my so far I would buy again.

I've had this running now for about 2 months. No problem with self-installation or instructions. So far, it's been working perfectly for both heat and ac. It is so quiet that it is hard to tell if its running. I would recommend this unit but be aware that it does not have auto swing from left to right as stated in features, but they can be manually positioned. I also don't believe it has the follow me feature as well, but I don't see the need for it. At this point I have no regrets with this unit and hope to get many years of use.

I purchased this .75 ton single zone system for my master bedroom which is always hotter than the rest of the house. So, this is providing supplemental cooling to a room. I was lucky to have an ideal situation of having space on an exterior wall in the room so the heat pump could be placed just on the other side, with an electrical subpanel within 10' of the unit. So, very straight forward install. I purchased a 2 3/4" hole saw to make a clean hole on my interior drywall, then used a small masonry bit to make a series of small holes in a circle on the outer stucco wall, being careful to create a slight downhill slope from inside to outside.Some comments about the instructions that come with the unit:- the description of wiring connections refers to colors that didn't exist with the kit that I purchased. In the end, colors don't matter a bit, just make sure the order is identical for connections 1,2,3 and ground on both sides of the control cable.- the manual mentions in bold letters to be sure to plug the drain in the drain tray using the supplied plug on the side opposite of where the drain hose is coming out, since it is designed to support either left or right side drains. I couldn't find any plug, so I called support. They said ignore, it's already installed at the factory, and since I didn't need to change it to the other side I was fine.- the manual mentions to test your drain by removing the filter screens and pouring water into the tray. This is not obvious where to pour the water. Tech support said to pour over the evap coils. My first try I poured a little too far back and water ran down my wall. Then I poured a little close to the front and water ran out the drain line like it should, with no leaks.- the very good news is that tech support is available. I probably waited about 5 mins on hold to talk to a tech, and they were very helpful.Once the physical installation of the indoor and outdoor units was complete and the circuit was run, I called my HVAC friend to come over and complete the install. He insisted that we cut the stock flares off the lines and reflare the ends, as the factory ends are usually flared with too much pressure resulting in very thin flares. Sure enough, his flares were much thicker than the ones he cut off. Also, we found a piece of loose copper in one of the 5/8" flare nuts which would have caused leaks for sure. He then made the connections and used nitrogen to test the lines to 700psi for 10 mins, then pulled a vacuum for 10 mins. Finally when he was satisfied that all air was purged from the lines he open the valves to charge the system, and it works perfectly. I had pondered doing that part of the job myself by buying a vacuum pump and gauges on Amazon but I think I'm glad that I ended up paying a pro to do it instead. There are some hazards that only someone with a lot of experience would know to look out for.As some other have mentioned these units are unbeleivably quiet. If it weren't for the fact that I can see the fan moving on the heat pump, I wouldn't know it was running at all. It is really that quiet.Hopefully this will provide many many years of comfort!

The unit itself is OK. It's quiet and heats when you set it to heat, and cools when you set it to cool. Auto mode doesn't work, but that's not the point. If I could give 0 stars for the purchase and return experience, I would.DO NOT BUY unless you're willing to accept you'll have to pay half the cost of the unit (at best) to be able to return the item, even if it's still in its original packaging, shrink-wrapped on its original pallet.I bought the 6000 BTU unit, and it arrived with a leak (the box was even wet). I spoke with an HVAC tech and they said it would be cheaper to buy a new unit than repair it, so I went ahead and started a return and ordered a new unit. In the meantime, another HVAC tech contacted me and said he could actually repair it for around $400, so I did that and tried to cancel the new order, but it was too late.The response to the original return was that I would be responsible for the cost of return shipping (around $230 at best) and charged a restocking fee with a minimum of 20% of the cost of the unit (so another $130). That was if the unit was in brand new condition in original packaging. Mine arrived broken and the boxes were destroyed, so that fee would have been even higher (up to 50%, so about $325). To return a broken item, I would have to pay almost the same amount of money as I would just buying a whole new unit. This is not a "return policy".They said they could arrange a pickup of the old broken unit and send out a replacement. I thought "okay, awesome", and said I already ordered a replacement that had just been delivered. They said that couldn't be treated as the original's replacement, and I'd still have to pay for return shipping on whichever one I returned. So I'm back to having this $650 mini split in its original box, shrink-wrapped on its original pallet unless I want to spend a minimum of $360 to send it back for ~$300 in a refund if I'm lucky and it doesn't get damaged in shipping. No thanks. Never buying from this company again, and doing whatever I can to prevent anyone else from making the same mistake I did.This all could have been prevented if I could just treat this new unit as a replacement for the old one.