Drive Medical 770-626 AquaSense Raised Toilet Seat with Lid, Standard Seat, White

Fits my toilet perfectly and solidly. As the ad states, this is a 4" riser, but the ad also states incorrectly that it is a 5.1 cm riser. 4" equals 10 cm, and this information is given correctly on the box.The lid is very thin and light but that's good, not bad, as far as I'm concerned. Most of the reported problems are when the seat does not fit. The INSIDE dimensions of my toilet boil are 11.0" left to right and 13.5" front to back. Some sellers say this seat is for "round" toilet bowls but NO toilet bowls are round. ALL toilet bowls are elongated. The version that's sold for "elongated" toilets would not, I'm sure, fit my toilet, even though my toilet is 2.5" longer front to back than it is left to right. A more proper description is that this seat is for toilets with a standard elongation and the seats for elongated toilets are for toilets with a more pronounced elongation.I had no problem installing the seat in less than a minute. Removing the old seat took about 3 minutes. The plastic clamps work extremely well on my toilet and the seat does not slide or rock at all.It appears that I could have left the existing seat and lid on, (in raised position.. it would not be possible to lower them with this AquaSense seat in place). However, I needed to replace my existing seat anyway since it was cracked, and this does the job perfectly, raising the seat by 4". I'm tall, but the 4" rise would not be a problem, I'm guessing, even for someone 5' tall unless the toilet was tall to begin with. With this raised seat installed, the seat is now 18" above the floor in my bathroom. That's the same height as the seat of a standard dining room chair.

I love this toilet seat with lid! I recently moved into an apartment that has a 'child size' toilet! (so ridiculous!)I mean it's small and low to the floor! Within just a few days my knees(with osteoarthritis) were killing me... couldn't get off the toilet without pain throughout my knees and traveling up my legs a little! This toilet seat is perfect! It's comfortable and sturdy and I can stand right up now without all the pain! And it looks decent too. Not like those big old awkward ugly beige seats that elderly people had to use in the past! Took my son just a few minutes to install it (right on top of the original toilet seat) My kids are also impressed and said that I do not have to remove it whenever they come over. I also have a small stool in there that the smaller Grandchildren can use to get up there. This has turned into one of the most important purchases I've made in a long time and I urge you, if you have bad knees,(like me), to just buy it! Also, it IS returnable if you don't like it for some reason! As for me....I'm so happy with the purchase!

It worked perfectly for almost two weeks, but then suddenly it would not hold it's position at all. It kept sliding around. I assume it was flexing the clamps, and no amount of adjusting helped. The bit on the front that should brace it from going backwards and help hold it in place just stopped doing it's job. It makes no sense, I can't explain it, and it's not returnable.If I can find a way to make it stay in place I might try it again, we'll see

After trying a few risers in recent years (having an Osteoarthritic knee), I was wanting to replace one I had liked by another seller, but had a weak “lid attachment” to, having easily broken off. After ordering this one, I found the seat is a FLATTER design, instead of the “molded” model, yet the marketing photos for this version have it APPEAR to be the prior style, which it is not. (This is not the first time I experienced this, getting once from elsewhere and having returned immediately, since the box and site photos depict the more sculptured seat version of, shown in my comparison photos). I don’t know if others are aware of.Not having enough “padding” on myself, it is a harder, flatter surface for me, liking the more “curved” model. Also, a mistake I made is having had the last one be a 6” height increase, this one is 4” high, so I feel the difference. However, my being in need of and not finding an option, I am having to adapt to this “flatter” seat. I am motivated to do so, since it also has a slightly better LID attachment connector - still to be careful to not put weight upon closed lid. (Having a cat, whom had been jumping upon my previous riser lid).ALL THAT being said, THIS style of riser with lid to me has been the easiest to attach and maintain, and will continue to use. * Those having trouble with it remaining stable, I had found the knobs need to be screwed in opposite directions (right knob - back, and left knob, forward, while testing for a secure fit). This is a better option than having to deal with removing bolts and adding a riser with no lid.

I bought this to help me with my total knee replacement surgery. I'm about 250 lbs and read the reviews about being unstable or low quality. Maybe the lot mine came from was after some updates had been done.It's easy to install (you must uninstall your existing toilet seat cover, and when you tighten the new one in, don't try to be a Hulk and over tighten. I'm only 4 days in to using it, but it's solid, doesn't wiggle around and raises me to a decent height.Since it's raised, it is a little more difficult to clean the toilet, not by much, and men can't just lift a lower lid when they pee (there is no lower lid) but it works excellent for the person who it was intended for.. someone with a recent knee or hip surgery that needs a raised seat temporarily.I would recommend at this time.