Key Fob Keyless Entry Remote fits 2004-2016 Toyota Sienna (GQ43VT20T 6-Btn)

Works great and has lasted a few years so far. Programming these to the car is a bit of a challenge but if you can follow directions, you'll have a good remote.

Product came with a website link to programming instructions. They were a little more difficult to follow so I included some easier ones here.What was not made clear at least to me in the instructions is you have to reprogram all of the remotes. So the first time I did it I only the new remote worked. After reentering programming mode I reprogrammed all the remotes. I used the instructions as follows.Programming Notes:Remove the key out of the ignition cylinder. Keep driver’s door open and unlocked, while leaving all other doors closed.Within 5 seconds or less:– insert the key in the ignition and then pull the key out– insert the key in the ignition and then pull the key outWithin 40 seconds or less:– close and then open driver’s door– close and then open driver’s door– insert the key in the ignition and then pull the key outWithin 40 seconds or less:– close and then open driver’s door– close and then open driver’s door one more time– insert the key into the ignition cylinder, but leave it inside at this time– close the driver’s door– turn the key to ON position, but do not start or crank the engine– turn the key back to OFF position– remove the key from the ignition cylinderWithin 3 seconds, the power door locks should lock and then unlock automatically indicating that you have successfully entered the programming mode. Return to step 1 if the door locks did not cycle at this point.Within 40 seconds or less:– Simultaneously press lock and unlock buttons on the remote that you are trying to program for 1.5 seconds– Let go of the lock and unlock buttons, and then press and hold the lock button for 2 seconds. Within 3 seconds, the power door locks should lock and unlock once automatically, indicating that you have successfully programmed the new remote.If the door locks cycle twice, then there might a problem with the transmitter or the procedure. In that case, repeat step 6 or verify that you have correct and properly working transmitter.To program more than one remote, repeat step 6 for each additional remoteFinally, open drivers door to exit programming mode.

The link to the instruction video made it 1 min programming. Works on my Toyota sienna 2007 in less then 2 min.

4 stars.- 1 star based on the fact that(1) this FOB feels of lower quality than the OEM. Plastic feels thinner.(2) rear door buttons are slightly depressed so it takes more press to activate the fob. Not sure if this will wear it down faster with repeated use.Programming was easy and straightforward.1. With all doors closed, and the key out of the ignition, only unlock and open the driver door.2. Within 5 seconds,Insert the key into the ignition (Do NOT turn it) and Pull the key out. Repeat one more time.3. Within 40 seconds,Close then open the driver door.Repeat one more time.The, insert the key into the ignition (Do NOT turn it) and Pull the key out.4. Within 40 seconds.Close then OPEN the driver door.Repeat one more time.Insert the key into ignition and leave it in the ignition.Now CLOSE the driver door.Turn the ignition to ON then back to OFF (Do NOT start or crank engine).Remove the key from the ignition.5. Within 3 seconds, the power door locks will lock then unlock automatically indicating successful entry into programming mode.Return to step 1 if the door locks do not cycle at this point.6. Within 40 second,A. Press the lock and unlock buttons on the remote together at the same time for 1.5 seconds.B. Immediately after letting go of the lock and unlock buttons, press and hold the lock button by itself.Within 10 seconds, the door locks should lock and then unlock once indicating successful programming.(If the door locks cycle twice, repeat steps A and B in step 6 as the remote was not accepted)Repeat steps A and B in step 6 for each new remote.7. Test remote FOBs. Try all buttons.

Got a used Toyota that only came with one master key and one remote, plus the valet key. Needed another master key and remote, this was good value for the remote. Got an OEM key from another vendor than Amazon, better price even with shipping. Rented a programmer from Tom's Keys, got the key blank cut at Ace, then coded both up with the programmer. Working just fine. Helpful note if your using Tom's Keys - their instructions say to code the key FIRST then get it cut. The programmer will work fine if you cut it first; the instruction is really meant for the keys you buy from them, if it won't code up for some reason they might not warranty it if its already cut.

Said it could be programmed for my make and model. It couldn't. Rip off

WOW!!! I thought the video was a joke, but it is really to program the remote! I was hesitate to do it! Look so confused!So, I watched the video several times until I am familiar with it. Then I do it along with the video. As soon as the video finished, I finished!!!Very EASY!!! This is my first time and I proud of myself saving $75 for other people to program.

No fue lo que esperaba se me aruino muy promto, no funciona màs.