MoKo2-Pack Matte Screen Protector Fits Kobo Libra Colour 7 Inches 2024/Kobo Libra 2 E-Reader 7" 2021, Premium PET Anti-Glare Screen Protective Film Screen Protector

I was offered a refund. Honestly these work ill center them better next time maybe it wont matter. I dont see any others with good reviews at all. And some dont do kobo libra color or kobos at all. It still works.Ive made notes on how to apply them. Ill update again . Too short small uncovered bit at bottom of my screen.Also unclear directions it says take off sticker side 1 not clear that you should put side 1 on the e-reader. It does not feel sticky at all until it touched the screen. So I have a Kobo Libra colour and the 2nd screen protector was too short. So it's not on very good . Cause I don't do screen protectors all the time. So side 1 is the sticky side in this pack anyways .

What are the guide stickers for?!!!!??? His do you use it!?!?!! The instructions are terrible. I got the two pack because I thought I'd need the extra for practice... But I've had trouble using both and both are garbage now.Edit: I ordered another 2 pack because I do need a screen protector on my device :/ Ruined one but the last one worked!! I had the "#1" and "#2" stickers on the top edge of the screen, then added 3 guide stickers along the bottom, vertically, just like the stickers on the protector, then wrapped them around the bottom of the device so they'd stay put. Then I somehow removed the bottom edge of the bottom layer - so that I could install the protector without pulling off the entire bottom layer at once. And honestly, I just moved quickly and squeegeed quickly and hard. There's maybe one tiny bubble but I'm not bothered.

As other reviews state, the protectors are a little hard to put on because somehow they attract a lot of tiny dust bunnies that you can’t see and end up with a surprising amount of air bubbles (or maybe I had bad luck lol).It’s still touch sensitive so you don’t need a stylus to work your Kobo.I noticed though that it’s not as scratch resistant as claimed because I can see all the swirls and whorls of my writing and erasing. (Do those count as scratches?) it can be a little distracting especially in dark mode.Either way, I’d prefer the scratches be on the protector than the actual screen.

The media could not be loaded. This is a great screen protector. It went on without any bubbles and fits very well.. maybe even a little too well. It looks like it might be difficult to take off if I need to remove it. I honestly can’t even tell that there is a screen protector on. The screen cleaning and dust applicators were also very helpful. I really have no issue with the quality or fit of this though.I’m not sure if you’ll be able to tell from the photos but my only complaint is that with it being a matte screen protector I do notice that the screen quality has decreased a bit. The matte protector makes the font look a bit less sharp and adds a “fuzzy” look to the screen. This definitely isn’t the fault of the brand, it’s just the cost of having a matte screen cover. If that is going to bother you, then I’d say definitely stay away from this and get one that isn’t matte.

I don't understand the reviews on here stating that it takes a great amount of effort to apply one of these screen protectors to the Libra Colour. Or that people couldn't apply either & that they were ultimately a waste of money.The one thing I dread above all else when I purchase a new electronic is the installation of a screen protector, because they're always a pain to apply without screwing up the edges, and it can be difficult to avoid getting dust under it.I think it took me a grand total of two minutes to put one of these on my new e-reader. And half that time was me just wiping it down with an alcohol wipe, then drying it off with the cleaning cloth.Lining it up with the screen was a breeze, and I felt no need to use the guide stickers (I've never used said stickers before for any device of mine, because I just know they'd only serve to frustrate me further by adding in an extra step). I honestly think the negative reviews are due more to operator error than anything.All in all, I like the protector very much & am glad I got them. Now I don't have to worry about scratching up my screen with the stylus!

Great and fit the KLC perfectly.

I've installed a lot of screen protectors over my life. I've learned some tricks that help.1. Run the shower. The water vapor helps take dust out of the air. This is the best thing you can do to help you get a clean install.2. Use a hinge. Moko did provide some materials for this, but I prefer some duct tape. Duct tape also works to help remove any stray dust, kind of like the dust removers that are supplied.3. Leave the factory protective coating on until you can apply the screen protector. You can still clean the screen with the alcohol wipe. If you have a blower for photography lenses and sensors it can be helpful.4. Work from your hinge either down or across using the supplied card or a credit card to get out bubbles. Don't take the the entire backing off at the start. Peel it as you go working the bubbles out. If you get bubbles or dust, peel back up to the problem and deal with it. For dust use the adhesive from duct tape or the dust buster to remove.I did all of the above when trying to install on a brand new Kobo Libra Colour. It was really tough to get a bubble free install. I ended up ditching the screen saver because I wasn't happy. I managed to do better on the second one but still ended up with a couple of tiny bubbles near the edges. The bubbles aren't noticeable except to me and are invisible when the reader is turned on. I will say that I do really like the antiglare finish. It's also very nice to write on.Also, I don't generally take the top protective layer off until I have the screen saver installed. For this install I found it difficult to see bubbles with the top layer on. I took it off initially for my second attempt.