Classic Precision-Fit Recoil Pad for Synthetic Stocks

Despite the product name, this is the same product as the Limbsaver Precision Fit Recoil Pad, which is printed on the packaging. It is an outstanding product--MUCH softer and more shock absorbing than the pad that comes from the factory on the Mossberg 590a1. I was getting a very mild soreness in my shoulders after putting 50 rounds at a time through my shotgun. It wasn't too bad, but this pad eliminated that. I could probably shoot 75 - 100 rounds now without becoming sore, and the recoil feels more muted. It's not an enormous improvement, but certainly noticeable enough to be a worthwhile upgrade. This part number (#10121) is the SMALLER of the two Mossberg-sized pads that Limbsaver makes. I had a full size synthetic stock, which would normally take the larger pad size. However, I wanted to reduce the length of pull for more comfortable shouldering of the weapon. I cut approximately one inch off the length of the stock in my table saw (using a 60 tpi fine cut blade). That shortened the length of pull nicely and reduced the end dimensions of the stock to 4-7/8" tall x 1-9/16" wide--EXACTLY the size the 10121 pad is designed to fit. Since I had cut off an inch of stock, I had to use an 1/8" drill bit to deepen the upper screw hole in the stock. I also had to drill a new lower hole (about 3/16" lower on the stock end than the factory hole). It worked great. I have a shorter length of pull and a much softer (Limbsaver) pad that fits so closely you would assume it came that way from the factory. If you look very closely at either side, there is about a fingernail's width of overlap where the stock is slightly wider than the pad for about 1-1/2" because the profile of the stock bulges just a bit more than the profile of the pad. It's so slight that even I--a confirmed perfectionist--am still totally pleased with the results. Simply put, it makes the entire shooting experience a little more comfortable.

Used previous reviews of Limbsaver SAKO 75/FINLIGHT SYN BUTT PAD to determine it was correct match for my new Tikka T3 Lite rifle which turned out to be correct advice. Good fit for my 7mm Rem Mag. I first resisted this purchase as I've never before had issues with rifle recoil and it seemed like a wimpy thing to do, however I changed my mind when I found this rifle to have most recoil of any of my magnum rifles. If you only sight in and hunt, this may not be the case for you. I reload and often put many rounds down range when attempting to develop the "perfect" load. I'm embarrassed to admit it, but the 7mm Rem Mag was putting a hurt on my shoulder during this process. I believe this was do to the "LITE" synthetic stock when compared to heavier wood stocks on my 308 Norma Mag and 30-06 Ackley Improved rifles that seem assist with recoil and accuracy. This is my second Tikka after previously bought 243 for which the accuracy was phenomenal. I'll make a long story short by saying the Limbsaver made the 7mm Rem Mag comfortable to shoot (compared to the pretty hard factory butt pad) which allowed me to re-focus on my shooting techniques which returned accuracy to what I had expected for the rifle. I would NOT buy Limbsaver for lower recoil calibers. I find factory pad is fine for 243. Hope this helps other Tikka owners.

Perfect fit that tamed the recoil of my firearm

This doesn't fit a stoeger exactly. On my p3000 I had to force a lot of reshaping and grinding to get it to insert into the stock. Also it's too long, so it does have some overhang over the top of the stock. The p3000 doesn't really come with a recoil pad, more of a butt plate, so this is better. I just wished it fit better. So if you aren't handy with a Dremel, don't get this one, but if you are just grind part of the inner lip off the top and bottom and then thin out the inner lip sides and it will insert. Then while tightening, you need to apply constant pressure to get the lower end to go near flush to the bottom. This procedure will get you closer. But, does it work? The answer is definitely yes. The stoeger p 3000 use to bruise my should and I couldn't shoot a box of bird shot. Now I can shoot all day with no discomfort. Excellent product just takes some dremeling.

Installed on a Panzer M4. While install is simple be advised I had to file down some of the plastic on the inside so it would fit in the stock. I was able to reuse the stock screws since this did not come with any but it all lined up and fight nicely. Definitely feels more plush than the factory pad so looking forward to taking it to the range.

Very nice product

Holy cow, This Limbsaver pad was made for the Remington 870 Marine Magnum. It fit it perfectly. I used the screws from the original pad which had actually melted. I guess from old age. Awesome shotgun, but the original pad just melted. This Limbsaver (Part number 10101) was not to hard to find, so that is why I specifically say it fits a 870 Marine Magnum. No sanding or grinding required, installs and fits perfectly. Enjoy, thanks

These fit the factory stock perfectly. As thin as the factory butt pad, but better recoil absorption. Works fine on a 338 Win Mag. A must-have for the Blaser R93 Professional synthetic stock. ( Note - this will NOT fit the R93 Offroad synthetic stock.)