Moon Bay Outdoor Wall Down Round Pagoda Light, High Volt, E26 Base Socket(excl), Modern Lantern Design, Die Cast Aluminum Body with Clear Glass Shade, Waterproof for Entryway,Porch,Doorway,(Black)

The overall value and design is great. Design is timeless and exerting was well constructed, esp glass which I was nervous about (esp against hail, dust storms). The only con was the mounting screws weren’t the Length needed for stucco foundation homes, so the mounting bracket had to be bent to make this fit. If the screws were longer or second set attached that would of been really helpful, as this project took longer due to this. Otherwise this is a very nice well made item abd I recommend.

Light looks great and well made. The bulb is totally sealed in glass so it is a little time consuming to change but it will stay clear with just a outside cleaning. It looks great with a flame LED light inside. I couldn't be happier and I didn't spend a ridiculous price for a light

I read the reviews and checked the sizing, but it is still larger than what I expected. it is a good fit for the location however, but be aware that it is fairly larger

As others have mentioned, I didn't get all of the parts. The cone nuts were missing. I ordered 2 more before I discovered they were missing. If the next 2 don't have all parts, Im sending them back. Sloppy!

First, I was given this product in return for my impartial and honest review. Thank you, Moon Bay.I needed a decent light for the back porch. The house siding and fixture where the old one was installed was, shall we say, flimsy. This product had no documentation with it -- maybe lost, or it had been a return, since it arrived in a smashed internal box. I've fixed things for my career, and it took some time to figure out a way of using what they sent me to mount it to the siding. I also needed some additional hardware -- screws, washers, etc. -- as may be seen in the photo. (Sorry if they are sideways -- that's Amazon's decision.)Be aware that it appears to be metric hardware. (Metric screws thread into the two mounting plates, and the black nuts are metric.) There are only two small black exterior nuts holding the light in place : they screw on to two screws, which have to stick out just the right amount. It's a study in close tolerances to get everything tight. At the end I managed (sort of), but I was grinding my teeth.Oh, and the wire nuts are rather tiny (not standard orange nuts, more like blue or white), so you may need 2 or 3 of those. Those in the assembly photo are mine.I will also need some sealant around the outside, and to fill the gap at the bottom, so bugs don't get into the back of the light plate. Of course, this is just my particular setup, and yours will certainly be different. Just bear it in mind, and make measurements before you assume this will fit. Again, if it mounts to any uneven surface -- like brick -- you'll need a sealant to keep insects out.Amazon's page says "100 W", which to me means a current capacity (I = P/V = 100/120 = 0.83A), so I wasn't worried about using a "100W" LED bulb (which isn't 100W, of course). Check your bulb's amperage.Changing the bulb entails removing four little screws holding the black guard in place. Heaven help you if you drop one, but the shield would probably still work with two screws. The glass enclosure then unscrews, about one turn. I forgot to take a picture. It's decently thick. But changing the bulb is not something you want to do regularly, so get good bulbs.[Note: It appears that there are two versions of this light, one having an open bottom. Mine did not, so I have to remove the whole glass enclosure. I think I would prefer the totally enclosed, both to keep the bugs out and for water protection, even if it’s more difficult to change the bulb. The point being, you may get something different.]Final analysis -- unless it gets rusty or something -- is that it's a decently made light, a hassle to install without docs, you may need some additional metric hardware, and sealant. For $25, you could do worse.

We ordered 3 of these light fixtures. 2 of them did not have all of the hardware and we had to purchase a few items in order to install - but very worth it! The light offers a new sleek look to our house and we're glad we have 3 of these! Highly recommend!

The media could not be loaded. I like that its metal. Very Sturdy and easy to install as per my electrician, but...** VERY DISCONTENT that it DOES NOT bring the 2 Black Finish nuts to hold lamp to wall plate. You cannot install without the two nuts. However, those nuts are in the instructions (see photo I posted)My electrician NOW NEEDS TO RESCHEDULE to install this for me when he find nuts that will work and paint them black. He needs to go to hardware store and buy two nuts and black matte spray can...costing me more money so the value for money NOW ITS LOST for not supplying 2 Dumb Nuts!!!Note: on my last image posted, is an EXAMPLE of a lamp outside my home with two finish nuts supplied by its manufacturer/maker.On the Amazon description it DOES NOT states anywhere that these 2 nuts are MISSING. Yet other customers are facing this nuisance of a dilemma.

Great looking lights. Pretty easy to install. Need two men to install and help hold it. One thing my husband mentioned is that the screws aren’t magnetic so he almost lost some screws trying to screw them on and they are small. You have to screw and unscrew to change the bulb.