New Rage Cycles Fender Eliminator Kit (with Turn Signals) Compatible with 15-18 Ducati SCRAMFUL

Installed it on my 2017 Scrambler Cafe Racer and made the bike look so much better.Although no instructions came with the item, installation was super easy. No need to splice any wires as the license plate light and turn signal lights each have the plug and play harness ready to plug*. No hyper flash and did not need to buy\use resistors. The turn signals are nice and bright, however the license plate LED isn't as bright as stock. I wish it was a bit brighter, but at least you can make out what the plate says from a reasonable distance back, so i shouldn't have any issues with the police.*I only ran into two minor issues (but not worth deducting a star). First was I needed to bend the pins inside the NRC turn signal harness downwards to make it fit in the Ducati's turn signal harness (Nothing major, but just in case you get stuck trying to jam the harness in; it should be a smooth slide and click once the pins align)Second are the two holes near at the bottom of the plate. You are suppose to bolt them up using the existing hex screw that holds the plastic [Door] bit which hides the cables. However, it was difficult to align all four holes once you get the top part bolted under the brake light screwed in. I was only able to align three of the four holes (even after light bending and loosening of the screws that go under the brake light).Honestly, I didn't bother bolting the hex screw back into place because there's enough pressure keeping the plastic in place without it ever coming off (it'll make sense when you install it and see it in person, trust me).

I recently purchased a 2018 ducati scrambler cafe racer and immediately knew I would have to upgrade the rear turn signal lights and remove the large wrap around plate holder. I previously installed anew rage cycles fender eliminator on a ktm1290r so know what to expect as far as build quality goes, which in this case is 8/10. After researching many fender eliminator options for the scrambler, I decided to go with the NRC one again. Some reviews said you would have to bend the mount a little so I was expecting to make some slight modifications to get it mounted. I was pleasantly surprised that all I had to do to make the mounts line up on the bottom portion of the tail piece was to slightly widen the bend of the mounting unit with hand pressure. My one complaint about the fit is that the light is not parallel with the tail framework as you can see in the photos. It would have been nice if they sat flush with the frame but instead the back end is lowered away from the frame and the front almost tucks up underneath it. It is still an extremely nice upgrade from the stock turn signals and removed a ton of unnecessary bulk for the license mount. I was concerned about visibility to avoid getting pulled over by the cops, but it actually is very visible from the rear, even at a small distance. The lights are bright and the plate light works great. All were easy plug and play with no wire splicing. The instruction sheet is lackluster and they do not have specific variations of the different scrambler models so be prepared to do a little troubleshooting but it's quite easy. Hardest part was getting the wiring rerouted along the frame for the plate light and then reconnecting the indicator lights. Overall very satisfied with the purchase and would recommend it to anyone looking to remove the large wrap around plate mount on certain scrambler models. Nrc could improve their mounting instruction sheet for specific models with better photos but anyone with some mechanical ability should be able to figure it out.

Looks great. But side bags will block the visibility on these. Otherwise the brightness is great and somewhat easy to install. Had to fish out the connecting wire for extra length but had plenty to work with after all said and done.

Stay far far away!! Horrible fitment. Either description was wrong or the product is made extremely poor. Whatever it is, avoid at all costs. Instructions are horrible and incomplete( you have to go to a website just to view it) .. This thing is a piece of junk!!! If I wouldn't have already torn down everything, I would send this pos back!!

Like most of NRC gear, it’s low quality build.You can get it to snap a nice photo, but it’s not made to last, fitment is mediocre at best. Cheap metal, packaging, etc

Absolutely love this product. My signal lights on my 2020 Ducati scrambler full throttle was stick out too much I wanted to clean up the look on my rear tail. It looks amazing. Also came with the plate light bracket. The lights are bright! Easy install, the most annoying part was moving the wires around to have the correct placement.

Slim nice appearance and functional

I like it a lot, but a few things to note...- I installed on a Sixty2- It does not come with instructions, which it really should. However, thanks to YouTube, you can easily find one.- Like Mr. Lam's review below, fitment is a slight problem. The holes don't line up properly, however, a quick phone call to NRC will reveal that removal of the storage tray first will help. However, reinstalling the storage tray will require some pushing to align the holes. NRC can really fix this by enlarging the longer holes at towards the end of the bike.- The right side of the LED does not sit flush with the fender panel. It creates a slight gap....annoying, especially for my OCD. Once it is seen, it can not be unseen!Overall, I really do like it.